Tuesday, October 25, 2011
How to change a thermostat on a 2003 hyundai tiburon and where is the thermostat at on my car? please someone
Take it to the mechanic.How to change a thermostat on a 2003 hyundai tiburon and where is the thermostat at on my car? please someoneit depends on if its a 4 cyl or a v6. On a 4cyl its located right above where the transmission connects to the block. If its a v6 it is located behind the inlet fitting and connects the two heads together. Follow the upper radiator hose from the radiator and you will find it.How to change a thermostat on a 2003 hyundai tiburon and where is the thermostat at on my car? please someoneThe thermostat is usually located in the housing where the top radiator hose is attached to the engine. I
How to change a thermostat on a 1993 Nissan Quest Van?
Follow the hose from the top of the radiator to the engine block. It will go into a housing attached to the block...should be heald on with 3 bolts. Remove all 3 bolts, lift up housing, pull out old thermostat, replace thermostat and gasket.
When finished, flush the cooling system to remove junk so you wont be replacing another one.
good luck, hope this helps.How to change a thermostat on a 1993 Nissan Quest Van?the actual question is my quest heater is not getting hot? or my van over heats do you think I need to replace the theromstat? Yes however the water bypass C shaped hose between the CYl heads in the middle of the timing cover and long top radatior hose need to be removed. You will need a thermostat silicone sealant 12mm universal socket several extentsions patience and those hoses mentioned before. Wire brush on a grinder is especally useful grinding off corrosion and gasket material from the thermostat housing. Don't forget to shine a flash light thru the radatior core see if it is plugged up with cottonwood seeds or chaffe. Sometime just washing the junk out cools off a van. sometime you will be replacing the entire cooling system water pump timing belt and all. Good luck 1993 is 15 years old.How to change a thermostat on a 1993 Nissan Quest Van?DAVE GO TO AUTO ZONE OR ANY PARTS HOUSE AND SPEND 20$ ON A CHILTON'S BOOK PUT IT IN THE BATHROOM AND WHEN YOU HAVE THE NEED TO READ IT WILL BE THERE.GOOD LUCK
When finished, flush the cooling system to remove junk so you wont be replacing another one.
good luck, hope this helps.How to change a thermostat on a 1993 Nissan Quest Van?the actual question is my quest heater is not getting hot? or my van over heats do you think I need to replace the theromstat? Yes however the water bypass C shaped hose between the CYl heads in the middle of the timing cover and long top radatior hose need to be removed. You will need a thermostat silicone sealant 12mm universal socket several extentsions patience and those hoses mentioned before. Wire brush on a grinder is especally useful grinding off corrosion and gasket material from the thermostat housing. Don't forget to shine a flash light thru the radatior core see if it is plugged up with cottonwood seeds or chaffe. Sometime just washing the junk out cools off a van. sometime you will be replacing the entire cooling system water pump timing belt and all. Good luck 1993 is 15 years old.How to change a thermostat on a 1993 Nissan Quest Van?DAVE GO TO AUTO ZONE OR ANY PARTS HOUSE AND SPEND 20$ ON A CHILTON'S BOOK PUT IT IN THE BATHROOM AND WHEN YOU HAVE THE NEED TO READ IT WILL BE THERE.GOOD LUCK
How to change old thermostat 2 wire to new thermostat?
The assumption is that this is a heating thermostat!
The wires are connected to the R or RH and the W terminals.
If this is a Cooling thermostat, then the wires are connected to the RC and the Y or Y1 terminals.
This is strictly generic information and may not apply to your situation, more info would be helpful.How to change old thermostat 2 wire to new thermostat?The new Thermostat will have directions in the package. If not or if you lose them, The red wire in the wall is + and the balck is - .How to change old thermostat 2 wire to new thermostat?I have a wireless thermostat installed. Never had any trouble with it. It interfaces with a receiver stationed on the furnance unit. No wires.How to change old thermostat 2 wire to new thermostat?If your old thermostat only had two terminals, it was either direct current, or heating only or cooling only. You will need to replace with the same type of thermostat. If direct current, check the polarity of the wires BEFORE hooking any up. If it is heat or cool only, it really doesn't matter which side of the switch you put the wires.How to change old thermostat 2 wire to new thermostat?Your question is not very clear. http://appliancequickfix.com/
may be able to help you. See if you spot your specific problem there.
The wires are connected to the R or RH and the W terminals.
If this is a Cooling thermostat, then the wires are connected to the RC and the Y or Y1 terminals.
This is strictly generic information and may not apply to your situation, more info would be helpful.How to change old thermostat 2 wire to new thermostat?The new Thermostat will have directions in the package. If not or if you lose them, The red wire in the wall is + and the balck is - .How to change old thermostat 2 wire to new thermostat?I have a wireless thermostat installed. Never had any trouble with it. It interfaces with a receiver stationed on the furnance unit. No wires.How to change old thermostat 2 wire to new thermostat?If your old thermostat only had two terminals, it was either direct current, or heating only or cooling only. You will need to replace with the same type of thermostat. If direct current, check the polarity of the wires BEFORE hooking any up. If it is heat or cool only, it really doesn't matter which side of the switch you put the wires.How to change old thermostat 2 wire to new thermostat?Your question is not very clear. http://appliancequickfix.com/
may be able to help you. See if you spot your specific problem there.
Changing the thermostat for a 1998 Civic?
the thermostat recently went on my civic so i went and bought a new one im pretty sure i know how to change it but i just want to make sure im right?? what is the correct way to change it?Changing the thermostat for a 1998 Civic?SOME of them are on the LOWER hose - not sure about yours.Changing the thermostat for a 1998 Civic?The side with the spring goes towards the engine.Changing the thermostat for a 1998 Civic?make sure your car is cold before u start the job. empty your radiator and turn the heater control to hot, and try to blow out as much coolant as u can to prepare the system to be flushed as now is the time to do it. follow the lower radiator hose up to the thermostat housing, remove the clamp and then the hose. there will be 2 10mm head bolts holdong the housing on as well as a third bolt holding ground wires, remove the ground wires and then the holding bolts. shove a garden hose down all your openings and flush till clean water comes out. put the new thermostat with a new gasket into place and reverse the removal steps. the TRICK to filling up the coolant. a couple of inches behind the thermostat, on the housing, is a bleeder for the coolant. because u flushed with water, pour pure coolant up to 3/4 of a gallon in to the radiator. mix whats left with water to 50/50 and top off. fire up your car and look for any leaks. good luckglory hand cream xp
How to change a thermostat on a 98 honda passport?
digram of a thermostat on honda 98 passportHow to change a thermostat on a 98 honda passport?Some quotes from http://www.automotiveforums.com/vbulleti
%26quot;...thermostat is right in front, under the coil packs and connected to the lower radiator hose by a %26quot;chevy style%26quot; water neck.
I know because I replaced it about 2 weeks ago during a cooling system service. The part was about $23.00 at the dealer. I get a discount there, so my cost was a few dollars less.
The coolant gauge was indicating halfway or better on the scale, now it goes up to about a third and stays there. The radiator hoses aren't nearly as hard with pressure as they used to be and the engine is much happier with adequate cooling.
When I was flushing the system, I couldn't run the engine with the radiator cap removed, the water would gush out like an erupting volcano. This was before I replaced the thermostat.
Another thing- the radiator's drain plug is located in a terrible position and is virtually useless. I ended up pulling the lower radiator hose to drain the water / flushing solution, this worked much better.%26quot;
%26quot;...thermostat is right in front, under the coil packs and connected to the lower radiator hose by a %26quot;chevy style%26quot; water neck.
I know because I replaced it about 2 weeks ago during a cooling system service. The part was about $23.00 at the dealer. I get a discount there, so my cost was a few dollars less.
The coolant gauge was indicating halfway or better on the scale, now it goes up to about a third and stays there. The radiator hoses aren't nearly as hard with pressure as they used to be and the engine is much happier with adequate cooling.
When I was flushing the system, I couldn't run the engine with the radiator cap removed, the water would gush out like an erupting volcano. This was before I replaced the thermostat.
Another thing- the radiator's drain plug is located in a terrible position and is virtually useless. I ended up pulling the lower radiator hose to drain the water / flushing solution, this worked much better.%26quot;
How do you change a 1999 Dodge Durango thermostat?
look it up on autozone.comHow do you change a 1999 Dodge Durango thermostat?easy follow top radiator hose back to motor remove hose and two bolts in housing lift it off thermostat wil be there clean off old gasket replace not hard this should do it since most every car or truck sam e way
So can i change the thermostat my self or do i need to ask a mechanic?
It depends on how hard it is to get to. Newer cars use an O ring to seal the housing so its easy to do.Drain out enough coolant so the level is lower then the thermostat.Use the right size wrenches to unbolt it and take out the old one.Make sure you put the new one in the right way or it wont work.
By the way, never run your car without a thermostat.More on that with another question.So can i change the thermostat my self or do i need to ask a mechanic?You can change temperatures on your thermostat yourselfSo can i change the thermostat my self or do i need to ask a mechanic?Just repeat after me %26quot;I THINK I CAN, I THINK I CAN. Of course you can!So can i change the thermostat my self or do i need to ask a mechanic?Go buy a Chilton's Manual for the year and make of your car and it will give you step-by-step instructions on changing your thermostat yourself.So can i change the thermostat my self or do i need to ask a mechanic?It's pretty straight forward. As long as the Thermostat is accessible and you've drained enough Fluid and of course the proper tools to do the Job. Most importantly plenty of time so you don't rush yourself. Good LuckSo can i change the thermostat my self or do i need to ask a mechanic?Depends on what type of vehicle it is. The newer they are, the harder they come!So can i change the thermostat my self or do i need to ask a mechanic?If you live in warm weather climate,lose the thermosat you don't need itSo can i change the thermostat my self or do i need to ask a mechanic?Check out this site for FREE!
http://www.autozone.com/repair_info.htmSo can i change the thermostat my self or do i need to ask a mechanic?The thermostat is generally one of the more simpler jobs to do. You will need to ensure you have the correct model thermostat for your area and they can differ between icy and desert areas. Make sure you also get a new gasket at the same time. Whilst doing this job, check out the hoses and make sure they're still in good condition, otherwise you should replace them at the same time.So can i change the thermostat my self or do i need to ask a mechanic?if you are some what mechanically inclined then yes, if you don't know a pair of pliers from an Allen wrench then take it to a shop
By the way, never run your car without a thermostat.More on that with another question.So can i change the thermostat my self or do i need to ask a mechanic?You can change temperatures on your thermostat yourselfSo can i change the thermostat my self or do i need to ask a mechanic?Just repeat after me %26quot;I THINK I CAN, I THINK I CAN. Of course you can!So can i change the thermostat my self or do i need to ask a mechanic?Go buy a Chilton's Manual for the year and make of your car and it will give you step-by-step instructions on changing your thermostat yourself.So can i change the thermostat my self or do i need to ask a mechanic?It's pretty straight forward. As long as the Thermostat is accessible and you've drained enough Fluid and of course the proper tools to do the Job. Most importantly plenty of time so you don't rush yourself. Good LuckSo can i change the thermostat my self or do i need to ask a mechanic?Depends on what type of vehicle it is. The newer they are, the harder they come!So can i change the thermostat my self or do i need to ask a mechanic?If you live in warm weather climate,lose the thermosat you don't need itSo can i change the thermostat my self or do i need to ask a mechanic?Check out this site for FREE!
http://www.autozone.com/repair_info.htmSo can i change the thermostat my self or do i need to ask a mechanic?The thermostat is generally one of the more simpler jobs to do. You will need to ensure you have the correct model thermostat for your area and they can differ between icy and desert areas. Make sure you also get a new gasket at the same time. Whilst doing this job, check out the hoses and make sure they're still in good condition, otherwise you should replace them at the same time.So can i change the thermostat my self or do i need to ask a mechanic?if you are some what mechanically inclined then yes, if you don't know a pair of pliers from an Allen wrench then take it to a shop
Where is the thermostat in 1999 Toyota Avalon? Is it hard to change?
I see where the upper hose is attached to an aluminum pipe then to a housing sitting under the fuel injection system and dam near impossible to get to because of electronic wires. I can't believe any one would have placed the thermostat there. There has to be something I am overlooking. PLEASE help I am frustrated.
MikeWhere is the thermostat in 1999 Toyota Avalon? Is it hard to change?its on the engine end of the lower radiator hose, its easy to replace.
MikeWhere is the thermostat in 1999 Toyota Avalon? Is it hard to change?its on the engine end of the lower radiator hose, its easy to replace.
How to change a thermostat in a1990 f-250 diesel?
You will need to follow the top radiator hose out of the radiator and to the block. Unhook the hose from where it attaches to the block and there will be two nuts holding the fitting to the block that the water hose fits on. Underneath this fitting is the thermostat. Just undo the bolts and replace the thermostat. Pay attention to the way that the thermostat is laid into the block and be sure that you get it back in the same way. Also be sure that the truck has cooled as there will be some antifreeze spillage and that stuff create nasty burns. You should be able to do it be yourself without any problems.Looking for a Funky Duvet Cover how to cope with infidelity
How do i change out the thermostat in an 03 dodge neon??? anyone got a free online manuals???
my wife's car is over heating and it only does it from time to time... i know it's not the water pump, because if it was, it would overheat the whole time... i need to know where the thermostat is and how to replace it... does anyone have a free repair manual or know a site that has one??? i need to replace this piece ASAP...How do i change out the thermostat in an 03 dodge neon??? anyone got a free online manuals???The thermostat is not the problem it is the radiator. If the thermostat was bad the vehicle would overheat all the time. Take your radiator out and take it in to be cleaned, for about $60. It overheats at high speeds and usually with the air on. Thar's a sure sign that it's not your thermostat. Also there's a thermo switch connected to your radiator. Look for an electrical wire running to a switch connected to your radiator.How do i change out the thermostat in an 03 dodge neon??? anyone got a free online manuals???take off the upper radiator hose.
remove the housing on the engine block.
the thermostat is inside the housing
Make sure you put in a new seal and tighten to the recommended torque setting.How do i change out the thermostat in an 03 dodge neon??? anyone got a free online manuals???there are 2 10mm bolts that hold the housing behind the upper hose to the head. the new thermostat will come with an integral seal that has a locator tab so you cannot get it in wrong. start to finish it is a 10 minute job.
remove the housing on the engine block.
the thermostat is inside the housing
Make sure you put in a new seal and tighten to the recommended torque setting.How do i change out the thermostat in an 03 dodge neon??? anyone got a free online manuals???there are 2 10mm bolts that hold the housing behind the upper hose to the head. the new thermostat will come with an integral seal that has a locator tab so you cannot get it in wrong. start to finish it is a 10 minute job.
How do you change the thermostat on a 2001 nissan frontier 3.3 step by step and where is it located?
ok follow the top hose back to the motor will be inside that most of the time only two bolts....drain a bit of coolent,,, loosen the hose ,,, take out the bolts.... clean off old gasket... both sides ,,,, the part that is on the hose and the motor... use just a bit of blue silacone replace gasket make sure the thremostat is right side up tighten bolts and dont over tighten but do tighen them .... refill crank refill again check for leaks.. your done.... pretty easy most of the time....couple hours or less depending on how hot it is when you start and if you have the parts ready to go back.... is a can do at home thing for sure
How do i change a thermostat in my 92 jeep wrangler?
itsjustme,
i dont have specific instructions on your particular vehicle, and since you didnt say which engine you have, ill give you some general directions that will work for almost all vehicles.
make sure vehicle is NOT at operating temperature hot. (dont drive through death valley, hop out, and open the radiator cap) CARFEULLY open the radiator cap with a thick towel or rag, relieving any pressure in the system. CAUTION! coolant can reach over 250 degrees fahrenheit!
get a catch pan with at least a 8 qt capacity. for sake of ease, i wont go over draining some coolant from the radiator drain plug. remove upper radiator hose from thermostat housing bolted to engine. (clamps are usually 8mm) some coolant will come out. if you are reusing your old coolant, make sure to adjust pan on ground to catch as much as you can. unbolt thermostat housing, thermostat will either fall out or gasket / sealant will still hold it in. make sure to pay attention to if there are any holes or air bleeds around the outer edge of the old t-stat. you will want to orient the new t-stat in the exact same fashion as the one that came out.
[discard thermostat ONLY after making sure you have the correct thermostat and gasket. if you went to the dealer for the replacement part, (recommended) your new thermostat will look very much or exactly like the old one. if not, your new thermostat will almost certainly not look the same. be very careful making sure its the correct part, fit, and temperature rating. if mr. autozone employee asks you what temp rating you want, always go with original equipment rating. usually 192 - 195 degrees fahrenheit. always save parts until after the job is done! ]
clean all remaining bits of gasket / sealant from t-stat housing and where the t-stat housing bolted to the engine. be very very careful not to scratch or score any delicate mating surfaces! try to use some type of plastic tool to clean up mating surfaces. try not to use anything metal. even scotchbrite pads can make a mess of mating surfaces!
get ready for t-stat install. make sure if there is a hole or air bleed around the outer edge of the thermostat it gets installed in the proper position. (usually the highest point so air can escape) make sure t-stat does not get installed backwards!!!!! the side with the metal spring goes into the engine. on the back of the t-stat package is sometimes a diagram. if your vehicle uses a paper gasket, make sure gasket goes on TOP of the thermostat. if it has a rubber o ring that goes around t-stat, make sure o ring is on with no kinks or bends. you can use A LITTLE silicone sealant to hold the gasket onto the engine, trapping the t-stat between it and the engine. [make sure to let the gasket or o ring do its job: sealing the engine. silicone sealer DOES NOT seal. it only aids in proper gasket alignment and takes up any inconsistencies in the mating surfaces. just nod your head and zone out to anyone that tells you otherwise.]
bolt on t-stat housing. CAUTION. older parts that get hot and cold all the time tend to be brittle. nothing is worse than wrapping up a job on saturday night and breaking a part only the dealer stocks. be careful not to go crazy tightening the bolts that hold the housing on!
reattach upper radiator hose. do not overtighten clamp! (i recommend a new clamp EVERY time its removed) clamps take not much at all to seal the hose theyre on.
pour old antifreeze into radiator.
[now is a great time to change your antifreeze completely, although beyond the scope of this article]
if you lost a significant amount (more than 6oz) make sure to refill the radiator with a half and half mix of water and antifreeze as long as you didnt buy the premixed antifreeze. [these are a waste of money] if in doubt about what antifreeze to use, consult your owners manual or the jeep dealer. [ people tend to group coolant / antifreeze by color. not always the best way. go with equivalent to jeep specifications]
do not pour coolant all the way up to the top of the radiator neck if your jeep has one. i seem to remember jeeps having a radiator overflow tank. this will be your fill point. fill with coolant mix to %26quot;COLD%26quot; fill line.
[ignore cooling system additives they are a waste of money. if you stay on top of your maintainence, you will never need them. especially sealers or lubricators!!!]
***CAUTION check and re-check and check again to make sure there are no tools on the engine or radiator shroud***
leave cap off of overflow tank. start engine. do not rev engine. keep very very sharp eye on overflow tank. you may see gurgling. this is trapped air escaping from inside the cooling system. this is normal. do not let coolant level fall too low or out of the overflow tank. %26quot;bleeding air%26quot; from the cooling system can sometimes take from 15 to 30 minutes. your vehicle should be about 20 minutes. sometimes you will see almost no activity in the overflow tank. if this happens you will sometimes see the coolant level drop suddenly. this is when the thermostat finally opens. WAIT at least 15 minutes. [an easy way to tell is LIGHTLY touch the upper radiator hose to see if its hot. a vehicle at operating temperature will have hoses almost impossible to touch for more than a second]
when the activity inside the tank calms down, fill the tank to the %26quot;FULL HOT%26quot; line. do not overfill. check for leaks anywhere you have worked. replace radiator cap or overflow tank cap making sure it is on all the way. its good practice to then wait a few more minutes to make sure nothing is awry.
the next day check coolant level in tank first thing in the morning. it should be at the %26quot;COLD FULL%26quot; line. it may be low. this is normal. fill to cold fill line with 50/50 coolant water mix.
remember,
* check antifreeze %26quot;strength%26quot; with prestone coolant checker or equivalent. most places carry the prestone brand and it will be easy to find.
*flush cooling system according to OE guidelines otherwise youll have major problems down the road. this is especially important in cold environments.
*never used recycled antifreeze. youd be surprised how many shops do. very surprised.
*there is no difference in brands of antifreeze. nothing you will ever notice. as long as they meet your OE specifications they are just fine. private brands and store brands make fine choices.
*there is a difference in aftermarket and OE t-stats. if in doubt, spend the few extra dollars and go OE.
happy motoring!How do i change a thermostat in my 92 jeep wrangler?i dont know but if you get fed up with your car can i have itHow do i change a thermostat in my 92 jeep wrangler?follow the radiator hoses to the block the thermostat is usally located under the top radiator hose where it connects to the block.
just unhook the top hose at the block pop out the old thermostat put the new one in. don't forget to replace the gasket to!!!How do i change a thermostat in my 92 jeep wrangler?supahtforyou's instructions were excellent.
I have a 1988 Cherokee with the 4.0L inline 6 cylinder engine, and if your Wrangler has a similar engine, then the t-stat is located in the t-stat housing on the top / front of the engine, where the big fat hose returns water to the radiator. To change it, you need to remove the fan shroud (a pain in the butt), and the radiator hose as well. The t-stat housing has 2 bolts - one is easy to find, the other is under and below, also a pain.
It's not a hard job to do, but time-consuming. I broke the neck on the first one I worked on because it is made from pot-metal, not very durable. It was a factory item, I could not get a replacement from a parts store, so be careful when removing the t-stat housing. In other words, don't be like me and use a metal hammer if the t-stat housing is stuck. Tap it gently with a wood block or a rubber mallet to break it loose.
Scrape off all traces of the old gasket using a putty knife or flat single-edge razor blade, on both the engine block and the t-stat housing. You might even need to use a wire brush, applied carefully on the remaining bits of gasket.
Use a new t-stat and make sure it comes with a fresh gasket. Using a bit of RTV rubber on both sides to help the seal is not a bad idea, either. Clean off the threads on the 2 bolts with wire brush, and either oil the threads or use an anti-seize compound.
Just read supahtforyou instructions and you will be fine.
While you are at it, you might consider replacing all of the rubber hoses on the radiator and heater core, if they are either hard and brittle, or soft and mushy. If you are really energetic, put in a new water pump. (The pump is a bigger job - need to remove more belts and the radiator fan.) Either replacement job will give you extra piece of mind, and you will avoid having a blown out radiator or heater hose or leaky water pump in the middle of the winter. If you replace the bottom radiator hose, remove and keep the coiled spring that is inserted into the original hose. It goes into the new hose. The spring is inserted to keep the hose from collapsing when the water pump is sucking coolant out from the radiator.
Total parts for t-stat, radiator %26amp; heater hoses, and water pump might cost about $100, plus $10 for coolant. You will save yourself at least $200, or more by doing the labor yourself.
Good luck.
i dont have specific instructions on your particular vehicle, and since you didnt say which engine you have, ill give you some general directions that will work for almost all vehicles.
make sure vehicle is NOT at operating temperature hot. (dont drive through death valley, hop out, and open the radiator cap) CARFEULLY open the radiator cap with a thick towel or rag, relieving any pressure in the system. CAUTION! coolant can reach over 250 degrees fahrenheit!
get a catch pan with at least a 8 qt capacity. for sake of ease, i wont go over draining some coolant from the radiator drain plug. remove upper radiator hose from thermostat housing bolted to engine. (clamps are usually 8mm) some coolant will come out. if you are reusing your old coolant, make sure to adjust pan on ground to catch as much as you can. unbolt thermostat housing, thermostat will either fall out or gasket / sealant will still hold it in. make sure to pay attention to if there are any holes or air bleeds around the outer edge of the old t-stat. you will want to orient the new t-stat in the exact same fashion as the one that came out.
[discard thermostat ONLY after making sure you have the correct thermostat and gasket. if you went to the dealer for the replacement part, (recommended) your new thermostat will look very much or exactly like the old one. if not, your new thermostat will almost certainly not look the same. be very careful making sure its the correct part, fit, and temperature rating. if mr. autozone employee asks you what temp rating you want, always go with original equipment rating. usually 192 - 195 degrees fahrenheit. always save parts until after the job is done! ]
clean all remaining bits of gasket / sealant from t-stat housing and where the t-stat housing bolted to the engine. be very very careful not to scratch or score any delicate mating surfaces! try to use some type of plastic tool to clean up mating surfaces. try not to use anything metal. even scotchbrite pads can make a mess of mating surfaces!
get ready for t-stat install. make sure if there is a hole or air bleed around the outer edge of the thermostat it gets installed in the proper position. (usually the highest point so air can escape) make sure t-stat does not get installed backwards!!!!! the side with the metal spring goes into the engine. on the back of the t-stat package is sometimes a diagram. if your vehicle uses a paper gasket, make sure gasket goes on TOP of the thermostat. if it has a rubber o ring that goes around t-stat, make sure o ring is on with no kinks or bends. you can use A LITTLE silicone sealant to hold the gasket onto the engine, trapping the t-stat between it and the engine. [make sure to let the gasket or o ring do its job: sealing the engine. silicone sealer DOES NOT seal. it only aids in proper gasket alignment and takes up any inconsistencies in the mating surfaces. just nod your head and zone out to anyone that tells you otherwise.]
bolt on t-stat housing. CAUTION. older parts that get hot and cold all the time tend to be brittle. nothing is worse than wrapping up a job on saturday night and breaking a part only the dealer stocks. be careful not to go crazy tightening the bolts that hold the housing on!
reattach upper radiator hose. do not overtighten clamp! (i recommend a new clamp EVERY time its removed) clamps take not much at all to seal the hose theyre on.
pour old antifreeze into radiator.
[now is a great time to change your antifreeze completely, although beyond the scope of this article]
if you lost a significant amount (more than 6oz) make sure to refill the radiator with a half and half mix of water and antifreeze as long as you didnt buy the premixed antifreeze. [these are a waste of money] if in doubt about what antifreeze to use, consult your owners manual or the jeep dealer. [ people tend to group coolant / antifreeze by color. not always the best way. go with equivalent to jeep specifications]
do not pour coolant all the way up to the top of the radiator neck if your jeep has one. i seem to remember jeeps having a radiator overflow tank. this will be your fill point. fill with coolant mix to %26quot;COLD%26quot; fill line.
[ignore cooling system additives they are a waste of money. if you stay on top of your maintainence, you will never need them. especially sealers or lubricators!!!]
***CAUTION check and re-check and check again to make sure there are no tools on the engine or radiator shroud***
leave cap off of overflow tank. start engine. do not rev engine. keep very very sharp eye on overflow tank. you may see gurgling. this is trapped air escaping from inside the cooling system. this is normal. do not let coolant level fall too low or out of the overflow tank. %26quot;bleeding air%26quot; from the cooling system can sometimes take from 15 to 30 minutes. your vehicle should be about 20 minutes. sometimes you will see almost no activity in the overflow tank. if this happens you will sometimes see the coolant level drop suddenly. this is when the thermostat finally opens. WAIT at least 15 minutes. [an easy way to tell is LIGHTLY touch the upper radiator hose to see if its hot. a vehicle at operating temperature will have hoses almost impossible to touch for more than a second]
when the activity inside the tank calms down, fill the tank to the %26quot;FULL HOT%26quot; line. do not overfill. check for leaks anywhere you have worked. replace radiator cap or overflow tank cap making sure it is on all the way. its good practice to then wait a few more minutes to make sure nothing is awry.
the next day check coolant level in tank first thing in the morning. it should be at the %26quot;COLD FULL%26quot; line. it may be low. this is normal. fill to cold fill line with 50/50 coolant water mix.
remember,
* check antifreeze %26quot;strength%26quot; with prestone coolant checker or equivalent. most places carry the prestone brand and it will be easy to find.
*flush cooling system according to OE guidelines otherwise youll have major problems down the road. this is especially important in cold environments.
*never used recycled antifreeze. youd be surprised how many shops do. very surprised.
*there is no difference in brands of antifreeze. nothing you will ever notice. as long as they meet your OE specifications they are just fine. private brands and store brands make fine choices.
*there is a difference in aftermarket and OE t-stats. if in doubt, spend the few extra dollars and go OE.
happy motoring!How do i change a thermostat in my 92 jeep wrangler?i dont know but if you get fed up with your car can i have itHow do i change a thermostat in my 92 jeep wrangler?follow the radiator hoses to the block the thermostat is usally located under the top radiator hose where it connects to the block.
just unhook the top hose at the block pop out the old thermostat put the new one in. don't forget to replace the gasket to!!!How do i change a thermostat in my 92 jeep wrangler?supahtforyou's instructions were excellent.
I have a 1988 Cherokee with the 4.0L inline 6 cylinder engine, and if your Wrangler has a similar engine, then the t-stat is located in the t-stat housing on the top / front of the engine, where the big fat hose returns water to the radiator. To change it, you need to remove the fan shroud (a pain in the butt), and the radiator hose as well. The t-stat housing has 2 bolts - one is easy to find, the other is under and below, also a pain.
It's not a hard job to do, but time-consuming. I broke the neck on the first one I worked on because it is made from pot-metal, not very durable. It was a factory item, I could not get a replacement from a parts store, so be careful when removing the t-stat housing. In other words, don't be like me and use a metal hammer if the t-stat housing is stuck. Tap it gently with a wood block or a rubber mallet to break it loose.
Scrape off all traces of the old gasket using a putty knife or flat single-edge razor blade, on both the engine block and the t-stat housing. You might even need to use a wire brush, applied carefully on the remaining bits of gasket.
Use a new t-stat and make sure it comes with a fresh gasket. Using a bit of RTV rubber on both sides to help the seal is not a bad idea, either. Clean off the threads on the 2 bolts with wire brush, and either oil the threads or use an anti-seize compound.
Just read supahtforyou instructions and you will be fine.
While you are at it, you might consider replacing all of the rubber hoses on the radiator and heater core, if they are either hard and brittle, or soft and mushy. If you are really energetic, put in a new water pump. (The pump is a bigger job - need to remove more belts and the radiator fan.) Either replacement job will give you extra piece of mind, and you will avoid having a blown out radiator or heater hose or leaky water pump in the middle of the winter. If you replace the bottom radiator hose, remove and keep the coiled spring that is inserted into the original hose. It goes into the new hose. The spring is inserted to keep the hose from collapsing when the water pump is sucking coolant out from the radiator.
Total parts for t-stat, radiator %26amp; heater hoses, and water pump might cost about $100, plus $10 for coolant. You will save yourself at least $200, or more by doing the labor yourself.
Good luck.
Why is my 97 chrysler concorde coolant boil over and running hot i change the thermostat,and there no leaks?
Make sure your fans run. And is it a 3.3 engine or a 3.5. Did it melt the reservoir. It can also be as simple as a radiator cap not holding pressure. They need to hold 16 lbs. of pressure so the coolant won't boil, if its not holding pressure it will boil over.Why is my 97 chrysler concorde coolant boil over and running hot i change the thermostat,and there no leaks?its the radiator cap i got the same car and was told the same dont listen i put a lot of money in mine and it was that cap
The gasket is blown in a way that the exhaust gas is getting into the water jacket and supper heating the water. Try this.
Fill the radiator up to the top. Leave off the cap and crank the car. If water comes shooting out of the radiator like a fountain it is blown.
If nothing happens try this.
Remove all the plugs and crank the car. When cranking look for water shooting out of the spark plug holes.
In either case the head gasket is blown.
Report Abuse
Why is my 97 chrysler concorde coolant boil over and running hot i change the thermostat,and there no leaks?poss. a blown head gasket, filthy radiatorWhy is my 97 chrysler concorde coolant boil over and running hot i change the thermostat,and there no leaks?Well it sounds like you have a blown head gasket.The gasket is blown in a way that the exhaust gas is getting into the water jacket and supper heating the water. Try this.
Fill the radiator up to the top. Leave off the cap and crank the car. If water comes shooting out of the radiator like a fountain it is blown.
If nothing happens try this.
Remove all the plugs and crank the car. When cranking look for water shooting out of the spark plug holes.
In either case the head gasket is blown.
My car is tore up and I have tried to change the thermostat, change the fans, and?
it still isn't working, the radiator hose feels tight and it gets hot what is the next thing to check, could it still be the thermostat or do you think it is what?My car is tore up and I have tried to change the thermostat, change the fans, and?Did you put the thermostst in properly ?? The part that looks like a bellows or accordion goes down into the block. Next is radiator, do you have circulation ?? let the engine get to operating temp with radiator cap off. Look in radiator and see if water is moving, If the water is bubbling(air bubbles) you have a leaky head gasket. Check your dipstick for moisture, water in oil will make a milky color. If this checks out , turn off the engine and put your hands carefully on the radiator core and feel for any cool spots. If you find spots that are cooler than others you have a plugged radiator which I suspect is your problem with the limited info. given.My car is tore up and I have tried to change the thermostat, change the fans, and?hi kitten try changing oil putting in radiator cooler and if it still gets hot drive with heater on it takes the heat out of the engine bayMy car is tore up and I have tried to change the thermostat, change the fans, and?It may have a blown head gasket. You can tell if you check the radiator hose when its cold and then there is no pressure. Then after you start it within a minute there is pressure already in the hose. also you may have whitish goup on the dipstick or oil filler cap. Just a guessMy car is tore up and I have tried to change the thermostat, change the fans, and?You have given us some information, but we don't really know what the problem is.
If the car is overheating, check to see if the fans are turning. I assume that you did replace the thermostat with a new unit of the correct heat range?
If the water pump has failed the car will also overheat.
Is the radiator restricted for flow, either coolant or the air over the core?
Some cars are also prone to an %26quot;Air Lock%26quot; where air is trapped in the cooling system and must be bled out.
Hope this gives you some direction.
Good Luck and Merry Christmashow long does it take to learn asp textbox
If the car is overheating, check to see if the fans are turning. I assume that you did replace the thermostat with a new unit of the correct heat range?
If the water pump has failed the car will also overheat.
Is the radiator restricted for flow, either coolant or the air over the core?
Some cars are also prone to an %26quot;Air Lock%26quot; where air is trapped in the cooling system and must be bled out.
Hope this gives you some direction.
Good Luck and Merry Christmas
Moms, did your internal thermostat change after having kids?
After having my son 10 months ago, I am now hot all the time...and I sweat way more. I didn't have this after my daughter was born, plus I have hypothyroidism which has always made me super cold natured. I swear, something inside has changed. Have y'all gone through this. (and yes, it's been a hot, humid summer (93 today)...but still, I now even sweat when everyone else is fine)Moms, did your internal thermostat change after having kids?Yes!!!! My temp was always low (around 97.5), so I was always freezing. Now, I can't even go grocery shopping without sweating.Moms, did your internal thermostat change after having kids?ooh yea. my mother picks on me all the time, in the winter now i dont even wear a coat. i am ALWAYS hot. i swear i even have hot flashes sometimes lol and i am only 21.Moms, did your internal thermostat change after having kids?I don't know about that, but I smell a lot worse, I give my hubby a hug and he asks me why I smell like hamburgers!Moms, did your internal thermostat change after having kids?Yes I agree! My son is 13 months old, and I also have hypothyroidism. I have always been the cold one lol. Now it seems like I am burning up all the time. Usually I dont even sleep under the blankets at night, and that used to be something that I had to do or couldnt sleep. I also have a daughter and fine after having her. There is a huge age difference though, my daughter is now 9 and my son is 13 months so I dont knowl. My hubby teases and says I am going through menopause lol. I was like I hope at 28 I am not heheMoms, did your internal thermostat change after having kids?yes. i can't share a same bed with my husband. if his leg touches me, i am soooo hot. i am way more comfortable on the couch. he hates it, but i need to my rest to be with our daughter the next dayMoms, did your internal thermostat change after having kids?Yes. I used to be cold all the time, but now I am warmer. I think it has to do with me being underweight before and not anymore, and possibly nursing (?--not sure about that one; just a theory).Moms, did your internal thermostat change after having kids?Yes. Me too. I am hot. I sweat. My boyfriend complains because I complain.Moms, did your internal thermostat change after having kids?Im with you on this one but i go both ways. Im either wicked hot and sweating like crazy or really really cold and wearing a sweater when its 35c outside i dont have a mid ground and theres no way its menopause or im setting a record!Moms, did your internal thermostat change after having kids?Yes, my thermostat is up since having Angela. I sweat more, too, and more easily. It's been so hot here in OH this week I can hardly stand it.
How do you change a thermostat on a 2001 Toyota camry V6?
thermostat is at the back of the engine (fallow the lower radiator hose). thermostat is at the back of the engine in the middle. Drain engine coolant, Remove air cleaner assembly and air filter, Remove the 2 nuts (holding the wire harness in place) and pull back the engine wire protector from the water inlet and cylinder head, remove the bolt, disconnect the inlet pipe from the water inlet, Remove the o-ring from the inlet pipe (this pipe connect the lower radiator hose to the thermostat housing), remove the 3 nut, water inlet and thermostat, Remove the gasket from the thermostat. install in reverse.
Change a vw beetles clock and thermostat?
I DIDN'T GET A MANUAL WITH MY USED BEETLE AND I WANT MY CLOCK IN 12 HOUR TIME, AND MY TEMPRETURE IN FARENHEIGHT.Change a vw beetles clock and thermostat?When you're car is off, press both the hour and minute buttons at the same time. Hold them until the clock switches from 24 hour to 12 hour. By doing this with the engine off, you keep the temperature reading in Farenheit.
'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?
Heater put out heat for one day after changing the thermostat. Any ideas? Young workmate is just a janitor with a baby and needs the car to get to work. Thanks!'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?Check the coolant level. They may have forgot to purge the air from the system.
禄禄禄'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?tell your buddy, after hes driven his car, shut it down and feel the radiator next to the fan, feel the fins of the radiator, if he feels cold spots, it needs flushing. in matter of fact, tell him to flush the entire cooling system.'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?Heater core???'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?As Mr. T says, recheck the coolant level. Also make sure the system has been bled correctly. Many cars have a bleeder screw on the thermostat housing or in one of the coolant lines. Loosen that bleeder screw with the van off and then fill the reservoir until fluid comes out then retighten.'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?things that affect heat,,,,1..coolant level...is air in system.?..2.heater blend door...stuck?..,,3 heater control valve...is hot water[coolant going into core]?.4 bad heater core...flush it out to see...5 waterump is bad...not cirulating coolant...6...thermostate is stuck...again...it happens..
禄禄禄'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?tell your buddy, after hes driven his car, shut it down and feel the radiator next to the fan, feel the fins of the radiator, if he feels cold spots, it needs flushing. in matter of fact, tell him to flush the entire cooling system.'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?Heater core???'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?As Mr. T says, recheck the coolant level. Also make sure the system has been bled correctly. Many cars have a bleeder screw on the thermostat housing or in one of the coolant lines. Loosen that bleeder screw with the van off and then fill the reservoir until fluid comes out then retighten.'97 Mercury Voyager van--changed thermostat for $130 but still running hot and blowing cold air?things that affect heat,,,,1..coolant level...is air in system.?..2.heater blend door...stuck?..,,3 heater control valve...is hot water[coolant going into core]?.4 bad heater core...flush it out to see...5 waterump is bad...not cirulating coolant...6...thermostate is stuck...again...it happens..
How do i change a thermostat on a 1997 honda civic?
I believe the thermostat is connected on the Lower Radiator Hose. Just look at the end of the hose that connects to the engine. Disconnect battery. Let car cool down. Remove hose. Remove 2 screws. Take off the thermostat housing. Pop the thermostat out. Put the new one in facing the exact same way! Reconnect everything ending with the battery. Oh and it helps to drain out like half of your car's antifreeze or water. I use water thats why I did not care if it spilled.programming lock file
How to change a thermostat of 1994 pontiac grand am
Well, if it's the 3.1 V6, and it's anything like the 95' Grand AM i had (yeah, i said HAD, LOL!), you got your work cut out for you. The thermostat housing just may be located in the area underneath the throttle body housing, so you'd need to remove all the rubber air intake junk (not hard to do). But after that, it's going to take a lot of patience and some nimble fingers to get the housing off to expose the actual thermostat. You will NOT get a socket in there - i remember i think i used the correct size small closed loop box wrench to get the 2 small bolts out, and it was like 1/4 turn at a time - this job took me about one full afternoon - but i never factored in the time i spent cussing , throwing stuff, and kicking things, and the couple brewskis i had to ingest to chill me out. Good luck
How to change a thermostat of 1994 pontiac grand am Follow the top rad hose from the rad and you'll find the thermostat housing , basically you must disconnect the hose clamp , then unbolt the thermostat housing and then the thermostat will be sitting inside of it.Pop the thermostat out , shove a soft clean cloth into the hole the thermostat came out of.
Scrape the surface of the housing where the hose is attached to and I recommend taking the hose right off of it so you can clean it better easiar.Scrape the other part of the housing and be sure all the old thermostat gasket is removed.
Make sure all the surfaces are clean and dry and use the factory recommended thermostat , install the thermostat right way up and apply a small beed of a high temperature gasket maker along the thermostat housing , then pop back the top housing into place , rebolt the housing , attache house and tighten clamp, add some anti freeze to over flow or rad, start up vehicle check the coolant level and watch for any leaks.
Hope that helps and best of luck.By the way the gasket maker is excellent to use bec it prevents most leaks and seals excellently.Plus get a service manual on your vehicle or go to the right parts outlet and you can get the free instructions and diagrams printed out to do this job too.
How to change a thermostat of 1994 pontiac grand am Follow the top rad hose from the rad and you'll find the thermostat housing , basically you must disconnect the hose clamp , then unbolt the thermostat housing and then the thermostat will be sitting inside of it.Pop the thermostat out , shove a soft clean cloth into the hole the thermostat came out of.
Scrape the surface of the housing where the hose is attached to and I recommend taking the hose right off of it so you can clean it better easiar.Scrape the other part of the housing and be sure all the old thermostat gasket is removed.
Make sure all the surfaces are clean and dry and use the factory recommended thermostat , install the thermostat right way up and apply a small beed of a high temperature gasket maker along the thermostat housing , then pop back the top housing into place , rebolt the housing , attache house and tighten clamp, add some anti freeze to over flow or rad, start up vehicle check the coolant level and watch for any leaks.
Hope that helps and best of luck.By the way the gasket maker is excellent to use bec it prevents most leaks and seals excellently.Plus get a service manual on your vehicle or go to the right parts outlet and you can get the free instructions and diagrams printed out to do this job too.
Change thermostat in 1998 Pontiac Grand AM V6?
What is an incomplete question, Alex?Change thermostat in 1998 Pontiac Grand AM V6?u mean how to change?Change thermostat in 1998 Pontiac Grand AM V6?I've done this job and it's not as hard as it
looks. The thermostat is located on the passenger side of the engine directly under the throttle body. You will have to remove the throttle body and unplug the attached wiring from it. Just make sure you put it all back like you found it. Drain the coolant so you don't make a big mess. Disconnect the hose going into the water neck. Take the water neck off and put your new thermostat in with the spring side pointing down. It comes with a new rubber gasket already installed so no gasket sealant is necessary. Put it all back together, refill with water and antifreeze, and you are done.
looks. The thermostat is located on the passenger side of the engine directly under the throttle body. You will have to remove the throttle body and unplug the attached wiring from it. Just make sure you put it all back like you found it. Drain the coolant so you don't make a big mess. Disconnect the hose going into the water neck. Take the water neck off and put your new thermostat in with the spring side pointing down. It comes with a new rubber gasket already installed so no gasket sealant is necessary. Put it all back together, refill with water and antifreeze, and you are done.
Im tryin to change the thermostat?
im tryin to change the thermostat in my 93 olds 88 royale and there is bolts that hold it together but there is a hose by the bottom bolt and i need to no what it is before i take it offIm tryin to change the thermostat?most likely a coolant hose for the throttle bodyIm tryin to change the thermostat?What I show is just a thermostat that is held on by two bolts and nothing else, the housing has a bleeder screw on it but I don't see what you are taking about.Im tryin to change the thermostat?What I show is just a thermostat that is held on by two bolts and nothing else, the housing has a bleeder screw on it but I don't see what you are taking about
How difficult is to change a thermostat in 2002 VW PASSAT 1.8T automatic? Can I do it by myself?
It's not all that difficult if you've got some basic mechanical ability. If I remember right, it's at the front of the car, on the left (from the front of the car) side. You'll need some decent channel-lock pliers or a pair of hose clamp pliers to pull the radiator hose off, then a largeish flat blade screwdriver to remove the squeeze clamp from around the thermostat itself, then it's just elbow grease and persuasion to get the old one out.
The very most important part about this job, make sure you get the right kind of coolant to put back in the car! You'll need VW G12, G12+, or G12++ type coolant, and yes, there is a difference between the VW stuff and the junk you can buy at your local auto store. Totally different make up, the everyday stuff, especially mixed with VW stuff, can eat straight through seals and gaskets.How difficult is to change a thermostat in 2002 VW PASSAT 1.8T automatic? Can I do it by myself?The previous poster is partially right, however the front end (bumper cover) needs to be removed. This is a difficult job. Keep in mind you need to flush and fill with G12, G12+, or G12++. Careful though, if you get air in the system, that will cause major problems.
The very most important part about this job, make sure you get the right kind of coolant to put back in the car! You'll need VW G12, G12+, or G12++ type coolant, and yes, there is a difference between the VW stuff and the junk you can buy at your local auto store. Totally different make up, the everyday stuff, especially mixed with VW stuff, can eat straight through seals and gaskets.How difficult is to change a thermostat in 2002 VW PASSAT 1.8T automatic? Can I do it by myself?The previous poster is partially right, however the front end (bumper cover) needs to be removed. This is a difficult job. Keep in mind you need to flush and fill with G12, G12+, or G12++. Careful though, if you get air in the system, that will cause major problems.
Where is the thermostat on a 99 Honda Accord? And do I have to drain the coolant to change it?
I would like to see a picture if possible.Where is the thermostat on a 99 Honda Accord? And do I have to drain the coolant to change it?Follow the upper radiator hose to the engine. Where it goes in is a housing and it is inside there. You do not have to drain the coolant, but it is advisable to flush the system and replace the coolant at the same time.how can i restadeletehedge one web hosting
Is a water pump any harder to change than a thermostat?
yes on most vehicles and easier to diagnos also. once you have the old thermostat out put it in a cup of water that is about 220 degrees Ferenheit give it a little bit and watch the plug of the thermostat which will be a tiny little disc with wax around it. if it opens you should see it if not replace itIs a water pump any harder to change than a thermostat?Depends on the vehicle, but yes 99% of the time the thermostat is much easier to get to. And much less expensive
How do i change my thermostat in my 05 tiburon 4 cylinder?
isn't it under warranty?
its at the motor end of the top radiator hose in the housing that the hose attaches to. make sure the new one goes in the same as the old one came out, and bleed the cooling system when you're done.
replace the thermostat housing gasket while you're at it- it will get destroyed when you separate the housing. and scrape all the old gasket off.
its at the motor end of the top radiator hose in the housing that the hose attaches to. make sure the new one goes in the same as the old one came out, and bleed the cooling system when you're done.
replace the thermostat housing gasket while you're at it- it will get destroyed when you separate the housing. and scrape all the old gasket off.
How to change the thermostat on a 2001 2.7l chrysler sebring?
need to know where it is located and how to replace itHow to change the thermostat on a 2001 2.7l chrysler sebring?Have it done at a shop Its not easy you'll have it towed there any wayHow to change the thermostat on a 2001 2.7l chrysler sebring?i acually did this the other day. its kind of behind the radiator where the hoses are connected to. the ones that go to the radiator. the thermostat is under that metal cover piece thing its got like 3 bolts on the cover. its easy all you have to do is first drain the anti freeze(get under the car and loosen the petcock), this may take a few minutes. when its drained disconntect the two hoses. then take off the metal cover and its inside there. be careful with the cover though because its very easy to break the gasket but its easy enough to get a new one.
good luck.How to change the thermostat on a 2001 2.7l chrysler sebring?The following instructions come from my Hanes Repair Manual #25040 for the replacement of a thermostat on the 2.7 L engine:
1. Raise the vehicle and place it securely on jackstands. Remove the right front wheel. Remove the accessory drivebelt splash shield.
2. Remove the accessory drivebelts.
3. Remove the lower alternator mounting bolt.
4. Lower the vehicle.
5. Disconnect the alternator electrical connectors.
6. Disconnect the electrical connectors from the air conditioning compressor.
7. Remove the oil dipstick and the dipstick tube. Plug the hole in the oil pan with a clean shop rag to prevent debris from entering the pan.
8. Remove the rest of the alternator mounting bolts and then remove the alternator.
9. Loosen the hose clamps and then disconnect the two hoses from the thermostat housing cover.
10. Remove the thermostat housing cover bolts and then remove the housing.
11. Note how the thermostat is installed, with the %26quot;jiggle valve%26quot; at the 12 o'clock position, and then remove the thermostat.
12. Remove all traces of sealant from the housing and coverr with a gasket scraper.
13. Install the thermostat housing cover and then tighten the bolts to the correct torque.
14. Reattach the hoses to the thermostat housing cover. Make sure that the hose clamps are still tight.
15. The remainder of the installation is the reverse of the removal.
16. When you're done, refill the cooling system.
17. Start the engine and allow it to reach normal operating temperature, then check for leaks and proper thermostat operation.
good luck.How to change the thermostat on a 2001 2.7l chrysler sebring?The following instructions come from my Hanes Repair Manual #25040 for the replacement of a thermostat on the 2.7 L engine:
1. Raise the vehicle and place it securely on jackstands. Remove the right front wheel. Remove the accessory drivebelt splash shield.
2. Remove the accessory drivebelts.
3. Remove the lower alternator mounting bolt.
4. Lower the vehicle.
5. Disconnect the alternator electrical connectors.
6. Disconnect the electrical connectors from the air conditioning compressor.
7. Remove the oil dipstick and the dipstick tube. Plug the hole in the oil pan with a clean shop rag to prevent debris from entering the pan.
8. Remove the rest of the alternator mounting bolts and then remove the alternator.
9. Loosen the hose clamps and then disconnect the two hoses from the thermostat housing cover.
10. Remove the thermostat housing cover bolts and then remove the housing.
11. Note how the thermostat is installed, with the %26quot;jiggle valve%26quot; at the 12 o'clock position, and then remove the thermostat.
12. Remove all traces of sealant from the housing and coverr with a gasket scraper.
13. Install the thermostat housing cover and then tighten the bolts to the correct torque.
14. Reattach the hoses to the thermostat housing cover. Make sure that the hose clamps are still tight.
15. The remainder of the installation is the reverse of the removal.
16. When you're done, refill the cooling system.
17. Start the engine and allow it to reach normal operating temperature, then check for leaks and proper thermostat operation.
Change default setting (68 degrees) of Honeywell thermostat?
Is it possible to change the default factory setting on my programmable Honeywell thermostat? Say to set it lower by one or two degrees? We don't need it this warm and I'm also trying to save money.Change default setting (68 degrees) of Honeywell thermostat?Go to their web site for info or call store for more help.
Any one know how to change the thermostat on a Hotpoint ff72p fridge/freezer?
The thermostat is basically the knob that you use to set the required temperature. Take the knob off, take the cover off, and you will see a switch with 2 wires on it plus an earth connection. Remove the wires, remove the fixing nut and follow the copper tube to the end, removing it as you go. You should finish up with a switch in your hand that has a copper tube attached to it. Take it to your local spares place, get a replacement, and fitting is a reverse of removal. Should take no more than half an hour.fish delegates
How do i change thermostat on a 1998 corolla ?
Get to the library and look in Chiltons or some other good auto repair manual, so you understand where everything is and how to handle it. Buy a thermostat and gasket. Drain your radiator. Open the thermostat housing and take out the old thermostat, watching which way the spring side goes so you can put the new one in the same way. Put on the new gasket and close up the thermostat housing and refill the coolant. Before you do this, look at your water pump carefully and feel around it. You want to know if it is leaking. There will be dampness behind the pulley and you will see a powdery, pinkish deposit in that area where coolant has dripped out and dried. If it leaks at all, replace it. That might be your whole problem. The job is easy.
Do not let that all aluminum engine overheat. Turn on your heater high to bleed off extra heat until you can pull over in a safe place and refill the radiator while the engine is running. Be careful opening a hot radiator or you could get scalded.
Do not let that all aluminum engine overheat. Turn on your heater high to bleed off extra heat until you can pull over in a safe place and refill the radiator while the engine is running. Be careful opening a hot radiator or you could get scalded.
How much does it cost to change a honeywell Zone valve which does not respond to one of my thermostat?
I was charged $650 of my hard earned money.I feel i was ripped royallyHow much does it cost to change a honeywell Zone valve which does not respond to one of my thermostat?Honeywell valves are not cheap. If you have a part number you can go to their web site and check the price.How much does it cost to change a honeywell Zone valve which does not respond to one of my thermostat?Drain the system
Change the valve
Refill and purge the system
FIre and check the system operation
What size zone valve
How large is the system
Were there other issues
Actually this price seems to be in line for this area.How much does it cost to change a honeywell Zone valve which does not respond to one of my thermostat?Sounds like a reversing valve which isn't cheap. I believe it involves some welding. So that is probably an average price.
Change the valve
Refill and purge the system
FIre and check the system operation
What size zone valve
How large is the system
Were there other issues
Actually this price seems to be in line for this area.How much does it cost to change a honeywell Zone valve which does not respond to one of my thermostat?Sounds like a reversing valve which isn't cheap. I believe it involves some welding. So that is probably an average price.
Where is the thermostat in a 1996 Chrysler Cirrus and is it easy to change?
Car is overheating. Just had water pump replaced.Where is the thermostat in a 1996 Chrysler Cirrus and is it easy to change?The best way I know to explain it is to tell you that when you open the hood, you can see the radiator cap on top of the engine, which is where the upper hose goes to.
If it's got the 2.0, or 2.4 liter engine in it (4 cylinder), then the thermostat is under that housing. Easy to replace.
If it's got the 2.5 liter 6 cylinder, then that is NOT where the thermostat is, it is in the housing that your lower radiator hose connects to. Not as easy to replace.Where is the thermostat in a 1996 Chrysler Cirrus and is it easy to change?thermostat is located by the lower radiator hose that go to the engine.
somewhere by the throller body.
is has a housing........
look at u'r radiator hoses.. there should be two..
one of them has a thermostat.
i did on my honda accord 2 weeks ago..
If it's got the 2.0, or 2.4 liter engine in it (4 cylinder), then the thermostat is under that housing. Easy to replace.
If it's got the 2.5 liter 6 cylinder, then that is NOT where the thermostat is, it is in the housing that your lower radiator hose connects to. Not as easy to replace.Where is the thermostat in a 1996 Chrysler Cirrus and is it easy to change?thermostat is located by the lower radiator hose that go to the engine.
somewhere by the throller body.
is has a housing........
look at u'r radiator hoses.. there should be two..
one of them has a thermostat.
i did on my honda accord 2 weeks ago..
94 Prelude overheating, but nothing hot under the hood. Change Thermostat already, what next?
I have a 94 prelude that i had the engine replaced in back in November. Everything was running fine, but the car would go past the middle point for temp when the car would sit for a while, but then it would go back to the middle point on its own.
Well, last saturday i was on a gravel rd and i peeled out and gravel kicked up and about 5-10 minutes later, i notice the temp gauge was all the way hot. I have changed the thermostat, blead the line, and refilled the coolant and the car gets hot is only about 1 minute. It literally goes from off and cool to all the way hot in about 60-90 seconds. Also, although the temp gauge is all the way hot, the radiator cap, plastic resovoir, no hoses, or the engine is hot. I take the radiator cap off and the coolant is not hot at all.
what is my issue. Please help?94 Prelude overheating, but nothing hot under the hood. Change Thermostat already, what next?Replace the temp gauge sensor and see if that's the culprit. Also, for $35 you can get a radiator cap with a build in temp gauge, so you can compare and see if your dash gauge is screwy.94 Prelude overheating, but nothing hot under the hood. Change Thermostat already, what next?the radiator cap %26amp; like the other guy said ur gauge might b messing up
have u changed ur waterpump???
Well, last saturday i was on a gravel rd and i peeled out and gravel kicked up and about 5-10 minutes later, i notice the temp gauge was all the way hot. I have changed the thermostat, blead the line, and refilled the coolant and the car gets hot is only about 1 minute. It literally goes from off and cool to all the way hot in about 60-90 seconds. Also, although the temp gauge is all the way hot, the radiator cap, plastic resovoir, no hoses, or the engine is hot. I take the radiator cap off and the coolant is not hot at all.
what is my issue. Please help?94 Prelude overheating, but nothing hot under the hood. Change Thermostat already, what next?Replace the temp gauge sensor and see if that's the culprit. Also, for $35 you can get a radiator cap with a build in temp gauge, so you can compare and see if your dash gauge is screwy.94 Prelude overheating, but nothing hot under the hood. Change Thermostat already, what next?the radiator cap %26amp; like the other guy said ur gauge might b messing up
have u changed ur waterpump???
How do you change a thermostat on a 2001 chevy monte carlo?
Take it to the dealer!!How do you change a thermostat on a 2001 chevy monte carlo?I don't think it is possible to change the thermostat in a 2001.
You might just want to look it up on yahoo.How do you change a thermostat on a 2001 chevy monte carlo??????????????3.1 or 3.8
using a 13mm wrench reach down/behind/and under the exhaust crossover pipe and loosen the bolt from there. if your lucky youll be able to finish it off by hand. also the bottom bolt doesnt need to be removed completely, back it out about 1/2inch and rock the housings top away from the engine and upHow do you change a thermostat on a 2001 chevy monte carlo?Get a Haynes manual and it should tell you everything you want to know about your car. These manuals are reasonably priced and a wise investment.How do you change a thermostat on a 2001 chevy monte carlo?Drain the antifreeze from the radiator. Follow the top radiator hose until it meets a metal housing, usually held by two bolts.Remove the top hose at this point. Remove the bolts and the housing may fall off or you must tap it with a plastic hammer. The thermostat is beneath the housing. Replace it with one with the same specs. as listed in your hand book in your glove compartment. I'd use an AC Delco or NAPA has a new top shelf version that reacts quicker to heat and pressure surges. Purchase a new O ring or gasket at the same time. Clean the faces of the housing and where it meets the manifold or block. Use a small amount of high temperature silicone sealer ( NAPA has this) to the face of the thermo. housing. Do the same on the opposite face on the intake or block surface. Be sure your antifreeze is clean. It calls for Dexcool antifreeze. If your old antifreeze is a dirty brown color drain and flush your system with a Prestone flushing kit. I'm sure you'll be fine!How do you change a thermostat on a 2001 chevy monte carlo?Removing the throttle body is a must to get to the bottom bolt, 13mm head bolt the housing is slotted at bottom bolt but you still amost have to have it completley out to get housing off.com and interop hair dryer
You might just want to look it up on yahoo.How do you change a thermostat on a 2001 chevy monte carlo??????????????3.1 or 3.8
using a 13mm wrench reach down/behind/and under the exhaust crossover pipe and loosen the bolt from there. if your lucky youll be able to finish it off by hand. also the bottom bolt doesnt need to be removed completely, back it out about 1/2inch and rock the housings top away from the engine and upHow do you change a thermostat on a 2001 chevy monte carlo?Get a Haynes manual and it should tell you everything you want to know about your car. These manuals are reasonably priced and a wise investment.How do you change a thermostat on a 2001 chevy monte carlo?Drain the antifreeze from the radiator. Follow the top radiator hose until it meets a metal housing, usually held by two bolts.Remove the top hose at this point. Remove the bolts and the housing may fall off or you must tap it with a plastic hammer. The thermostat is beneath the housing. Replace it with one with the same specs. as listed in your hand book in your glove compartment. I'd use an AC Delco or NAPA has a new top shelf version that reacts quicker to heat and pressure surges. Purchase a new O ring or gasket at the same time. Clean the faces of the housing and where it meets the manifold or block. Use a small amount of high temperature silicone sealer ( NAPA has this) to the face of the thermo. housing. Do the same on the opposite face on the intake or block surface. Be sure your antifreeze is clean. It calls for Dexcool antifreeze. If your old antifreeze is a dirty brown color drain and flush your system with a Prestone flushing kit. I'm sure you'll be fine!How do you change a thermostat on a 2001 chevy monte carlo?Removing the throttle body is a must to get to the bottom bolt, 13mm head bolt the housing is slotted at bottom bolt but you still amost have to have it completley out to get housing off.
Change Home Thermostat?
At this moment, I have at home two (one downstairs and one upstairs) Honeywell Thermostat model: T8401C (Digital non-programmable), I would like to upgrade my old one for the Honeywell model TH8320U1008.
I was thinking to do the terminal connection myself, but I wonder if I took out the cables from the old one, and put it in the same way in the new one... it is going to work?Change Home Thermostat?If your unit is heat only, the thermostat should have two wires (red and white). If it has central air conditioning or is a heat pump, you will have more than two wires.
The terminals on the thermostats should be labeled with letters such as G, R, C etc. Some new thermostats come with labels so you can mark what wires go to what terminal which helps make the project easier.Change Home Thermostat?yes. it's usually only 2 wires and they are usually color codedChange Home Thermostat?befor you buy, take off the cover from the old one and see how many wires you have. Write down the connector designation and color of wire, then go to the store and match it up with the new one. You may have a two three or four wire unit. air or no air? Is the white wire on the W connector? Is there a strap between two connectors?Change Home Thermostat?Just read the instructions, if you can't figure it out, call a pro!Change Home Thermostat?http://www.ewccontrols.com/acrobat/wirinChange Home Thermostat?The new ones, particularly if you buy them in a DIY-oriented place like Lowes or Home Depot, always come with very easy instructions. There are not many wires and they take you through the wiring step by step.Change Home Thermostat?Do the connections yourself. Just turn the power off the the furnaces first. If you can use a screwdriver and follow instructions you'll figure if out. However, if you can afford to go pick up $300 worth of thermostats you might as well let a professional do it. That way if something breaks you'll have someone to yell at. Good luck.Change Home Thermostat?You are dealing with low voltage. Turn the furnace switch off and follow the direction supplied. They usually give a toll free phone number to ask for help and advice. In general, the wires should be hooked up the same, but follow directions and/or call for aditional information. After intallation, turn the thermostate to a low setting and turn the furnace switch back on before you set the thermostate temerature. Follow directions.
I was thinking to do the terminal connection myself, but I wonder if I took out the cables from the old one, and put it in the same way in the new one... it is going to work?Change Home Thermostat?If your unit is heat only, the thermostat should have two wires (red and white). If it has central air conditioning or is a heat pump, you will have more than two wires.
The terminals on the thermostats should be labeled with letters such as G, R, C etc. Some new thermostats come with labels so you can mark what wires go to what terminal which helps make the project easier.Change Home Thermostat?yes. it's usually only 2 wires and they are usually color codedChange Home Thermostat?befor you buy, take off the cover from the old one and see how many wires you have. Write down the connector designation and color of wire, then go to the store and match it up with the new one. You may have a two three or four wire unit. air or no air? Is the white wire on the W connector? Is there a strap between two connectors?Change Home Thermostat?Just read the instructions, if you can't figure it out, call a pro!Change Home Thermostat?http://www.ewccontrols.com/acrobat/wirinChange Home Thermostat?The new ones, particularly if you buy them in a DIY-oriented place like Lowes or Home Depot, always come with very easy instructions. There are not many wires and they take you through the wiring step by step.Change Home Thermostat?Do the connections yourself. Just turn the power off the the furnaces first. If you can use a screwdriver and follow instructions you'll figure if out. However, if you can afford to go pick up $300 worth of thermostats you might as well let a professional do it. That way if something breaks you'll have someone to yell at. Good luck.Change Home Thermostat?You are dealing with low voltage. Turn the furnace switch off and follow the direction supplied. They usually give a toll free phone number to ask for help and advice. In general, the wires should be hooked up the same, but follow directions and/or call for aditional information. After intallation, turn the thermostate to a low setting and turn the furnace switch back on before you set the thermostate temerature. Follow directions.
I am a female atempting to change thermostat in a cryslerlebaron 1992 3.0 motor any good free sites to see how
Your best bet is to go down to Auto Zone or Advance Auto and pick up a Haynes Manual on your car. This will kill many birds with this stone cuz it covers the hole car and you all ways know where to find it.I am a female atempting to change thermostat in a cryslerlebaron 1992 3.0 motor any good free sites to see howgo to google and type car troubleI am a female atempting to change thermostat in a cryslerlebaron 1992 3.0 motor any good free sites to see howchanging the thermostat is any easy task to do. if you bought this vehicle used, and this is the first time that the thermostat is being changed, then better to get it done at the shop. The bolts that hold the thermostat housing on tend to be overstressed, and break when you try to take them off. Then, you could end up spending a paycheck getting the broken bolt out, having the block re-tapped, getting an odd sized bolt put back in the hole, and your antifreeze will leak out of this housing from now on.I am a female atempting to change thermostat in a cryslerlebaron 1992 3.0 motor any good free sites to see howPersonally I would recommend the Chilton Manual. I own both the chilton and the haynes and the chilton manual is better in my opinion. As said above it will help you out for the entire car.
Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?
Quick details- Girlfriend ran car alone on the expressway, lost heat. Called me, I told her to check temp gauge, it was topped out. Drove down to check car, no busted belts/hoses, coolant at a normal level. Changed thermostat, got heat for about 5 minutes, then got cold (though not as cold as the outside temp.). Temp gauge is reading perfectly fine but no heat at all. It is cold in Michigan. ThanksHeat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?probably air locked....should have a little bleeder type valve near the top of the engine, probably on one of the heater lines.....why did it overheat to begin with?Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?If the problem started after changing the thermostat, you probably have an air pocket in the line. This is keeping the hot radiator water from reaching the heater core and warming up your inside air.
Take it to a mechanic and have them get the air out.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?There is probably air in your heater core. Consult a repair manual on burping the cooling system. When burping run the car with the heater on. that will let the coolant flow through the heater core and pull the air out.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?You got an air bubble. Fill the radiator with the heat settings wide open for max heat coming out of the daskboard. run the engine til it is full hot -- 10 minutes at least. DON't gun it -- you'll break up large bubbles into small ones - harder to get it all out.
I f that doesn't work, run the engine til it's full hot, turn it off and pull the heater hose where it is at its highest point in the engine bay.... be ready to put it right back on.... You'll know if you got a bubble or solid water....
GM 2.8 Liter and 3.1 Liter motors from ~ 1986 to 1998 have a real pain in the *** bubble spot just behind the thermostat...... So trace your hoses if you're still stuck.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?I have a 2000 stratus with the same problem and now my blower motor resistor is going out have u gotten any good replys on this yet??
Take it to a mechanic and have them get the air out.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?There is probably air in your heater core. Consult a repair manual on burping the cooling system. When burping run the car with the heater on. that will let the coolant flow through the heater core and pull the air out.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?You got an air bubble. Fill the radiator with the heat settings wide open for max heat coming out of the daskboard. run the engine til it is full hot -- 10 minutes at least. DON't gun it -- you'll break up large bubbles into small ones - harder to get it all out.
I f that doesn't work, run the engine til it's full hot, turn it off and pull the heater hose where it is at its highest point in the engine bay.... be ready to put it right back on.... You'll know if you got a bubble or solid water....
GM 2.8 Liter and 3.1 Liter motors from ~ 1986 to 1998 have a real pain in the *** bubble spot just behind the thermostat...... So trace your hoses if you're still stuck.Heat doesn't work after a thermostat change, '98 Dodge Stratus 2.4 DOHC.?I have a 2000 stratus with the same problem and now my blower motor resistor is going out have u gotten any good replys on this yet??
What do you need to do to change a non digital thermostat to a programable digital thermostat?
Some of the newer thermostats require a neutral wire that goes back to the transformer. The place you purchased this new thermostat should be able to tell you if more wiring is needed. Good luck.What do you need to do to change a non digital thermostat to a programable digital thermostat?Before you decide to do this, make sure the digital thermostate does NOT need an electric source, for regular thermostats do not have one! IF the digital is battery operated, no problem.What do you need to do to change a non digital thermostat to a programable digital thermostat?You can't make a non-digital one digital, you have to buy and install a digital one. I always use Honeywell. The good ones are programmable and will save on your utility bills.What do you need to do to change a non digital thermostat to a programable digital thermostat?You just need the thermostat and instructions that come with it.What do you need to do to change a non digital thermostat to a programable digital thermostat?Remove the old thermostat, label the wires they should be color coded. The digitals come with very good instructions.What do you need to do to change a non digital thermostat to a programable digital thermostat?A phillips screwdriver and some masking tape to mark the wires and where they went before you disconnect them.What do you need to do to change a non digital thermostat to a programable digital thermostat?KNOW what kind of system you have first heat pump or just gas or electric they are different youll need some mollys the come with new t-stat and for gods sake get a honywell forget the hunter brand
How do you change a thermostat on a 1997 ford mondeo?
Follow the top radiator hose to it's end on a metal housing atop your engine. This domed out metal cover is usually secured by 2-3 small bolts into the block. The thermostat is contained inside, just lift it out noting it's position so you install the replacement properly. Replace the cover, tighten.Use any applicable gasket/sealant.How do you change a thermostat on a 1997 ford mondeo?I would drive into a Ford service bay and say %26quot;Hi, I am Janie Johnson. Can you fix my thermostat please?%26quot; :-)How do you change a thermostat on a 1997 ford mondeo?This is fairly %26quot;easy%26quot; to do. Please see this link:
http://www.automedia.com/Keep-Your-Eye-o
It is easy in that you %26quot;take off%26quot; and %26quot;put on%26quot;. But that's assuming that you have certain amount of mechanical ability. That's something only you can determine.
Good Luckhow to cope with a breakup kids hair
http://www.automedia.com/Keep-Your-Eye-o
It is easy in that you %26quot;take off%26quot; and %26quot;put on%26quot;. But that's assuming that you have certain amount of mechanical ability. That's something only you can determine.
Good Luck
Where is the thermostat on a 04 mustang located.?
I'm traveling from Atlanta to Albany and my vehicle is running hot. My reservoir is still full so I assumed that the thermostat is inop, and I need to change it. I've changed thermostats in GM vehicles but never worked on any ford vehicles.Where is the thermostat on a 04 mustang located.?The thermostat is in the same place, where the top rad. hose connects to the engine. If you would remove your radiator cap, with a cold engine, and idle the engine till up to operating temp. you can look in the opening and see the circulation. I would have a RADIATOR SHOP check it before I did any more. NEVER replace any part till you know the problem.
My toyota corolla overheat, I change the thermostat housing because of water leakage and still the car overhea
Various reasons for overheating- car out of tune, radiator leak, water pump problem, radiator fan not working, broken fan belt, etc. A good mechanic should be able to tell you the problem. Good luck!My toyota corolla overheat, I change the thermostat housing because of water leakage and still the car overheaturn on your A/C if the radiator fans comes on then its the temperature sensor switch not turning on the radiator fan PS The A/C requires the fan to be on so it sends a secondary source of power This lets you now the fan will function If it does look for the temperature thermal switch it is usually screwed into the radiator it will have two wires if you bridge them you complete the circuit and the fan will come onMy toyota corolla overheat, I change the thermostat housing because of water leakage and still the car overheaSound like the fan is not working, or it could be a sensor to tell the fan when to come on or it could be a radiator, could have a leak, or it could be your water pump not cooling the water.My toyota corolla overheat, I change the thermostat housing because of water leakage and still the car overheaWheres the water leaking from? It could be things from a fan to a porus block/head. Give us a little information and I%26quot;m sure we can help.
How do you change a Thermostat on a 94 honda civic dx?
usually, you follow the top radiator hose towards the engine. the aluminum piece the the hose is clamped to usually houses the thermostat. it usually has two bolts/nuts 10 or 12mm sockets should fit. change when engine is not really hot, as it will pour coolant everywhere when you take off the housing. pluck out old thermostat, pluck in new one. if there is a new therostat gasket available to purchase get one and put in place inbetween the thermostat housing and the engine when re-assembling. Its easy. You may have to take off the air cleaner and other misc items to get to that area, but still easy. I say %26quot;usually%26quot; so much because i cannot picture that particular engine clearly in my mind anymore, but all are about the same.How do you change a Thermostat on a 94 honda civic dx?No indication of why it needs to be changed. Did you check to see if the radiator has antifreeze. If the radiator does not have fluid then there is a leak. That needs to be repaired.
Not sure the thermo may be under the radiator cap or under the block hose that goes to the engine... Any way ya figure have to open the hood... If you try and change this object will probable need to buy $100 worth of tools...
Not sure the thermo may be under the radiator cap or under the block hose that goes to the engine... Any way ya figure have to open the hood... If you try and change this object will probable need to buy $100 worth of tools...
How do i change the thermostat in my pontiac montana 2004 ?
1. Drain the coolant
2. Follow the top rad hose down to the block
3. Remove the hose @ the block
4. Remove the thermostat housing
5. Remove the thermostat
6. Remove any gasket residue
7. Ensure surfaces are clean %26amp; dry prior to installation
8. Ensure the thermostat is installed the correct way around. [the spring side faces into the engine]
9. Refill the radiator [may have to loosen a heater hose to purge the air]
禄禄禄How do i change the thermostat in my pontiac montana 2004 ?The first 2 answers are correct. Sounds simple enough, except for the exhaust crossover pipe that is over the housing. Labor is 2.2 hours as long as it doesn't have A.I.R. pipes, then it goes to 3.0How do i change the thermostat in my pontiac montana 2004 ?Disconnect the upper radiator hose from the engine and remove the cover (2 bolts). Be sure to put the new thermostat in with the bulb down.
2. Follow the top rad hose down to the block
3. Remove the hose @ the block
4. Remove the thermostat housing
5. Remove the thermostat
6. Remove any gasket residue
7. Ensure surfaces are clean %26amp; dry prior to installation
8. Ensure the thermostat is installed the correct way around. [the spring side faces into the engine]
9. Refill the radiator [may have to loosen a heater hose to purge the air]
禄禄禄How do i change the thermostat in my pontiac montana 2004 ?The first 2 answers are correct. Sounds simple enough, except for the exhaust crossover pipe that is over the housing. Labor is 2.2 hours as long as it doesn't have A.I.R. pipes, then it goes to 3.0How do i change the thermostat in my pontiac montana 2004 ?Disconnect the upper radiator hose from the engine and remove the cover (2 bolts). Be sure to put the new thermostat in with the bulb down.
How to change the thermostat in a 1982 Corvette?
Assuming you have a carbureted 350(even if it is crossfire, same should apply). Remove the upper radiator hose that goes into the intake manifold. There should be two bolts holding the thermostat housing down. make sure the engine is cool and remove the two bolts. under the housing there will be a round metal diaphram lookin thing and thats the thermostat. you can just take it out with your hand and put the new one in. then put in the new gasket and hook it all back up.what is web hosting what is web hosting
Friday, September 23, 2011
Thermostat change in MX3?
My car doesn't ever seem to warm up or takes a very long time doing so. Someone has suggested that the thermostat is not working, but after doing some research I found that someone else changed theirs with no change. Could there be anything else wrong? It runs perfectly, but even though the heat gauge shoots up to half way shortly after running, it does not generate heat until it has run for quite some time, and even then very sparingly. Any idea how I can resolve this please?Thermostat change in MX3?Drain the coolant out of the radiator. Take the radiator off the car and fill it up with water and see if it comes out of the bottom of the radiator. If not the radiator is blocked which is causing your problem i have ahd this problem 4 or 5 times on mx3s and early mx5sThermostat change in MX3?it could be the heater matrixThermostat change in MX3?The radiator, in extreme cold, cools the coolant faster than the engine can heat it so your thermostat is closed more than open and coolant does not circulate properly. Therfore the heater can't put out warm air. You can partially cover your radiator to reduce the air flow and it will run hotter. Ever notice trucks with radiators partially blocked ?
I got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?
if you think is electric or vacuum. tell me where to locate it at. fuses are okI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?flush your radiator and heater core outI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?check your temp.sending unit and your heater core.I got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?There is a vacuum operated %26quot;mix motor%26quot; in the dash somewhere (sorry, not sure exactly where on the van) and if it goes bad, you will have no heat. If it fails the other way, you won't have A/C. As long as you're not smelling coolant in the cab, the heater core is more than likely ok.I got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?There will be a heater control valve located on one of the hoses going to the heater box on the engine side of the firewall
the heater control valve will either have a vacuum hose or a cable on top of it
if both of the hoses are hot you should have heatI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?if its vacuum, you are opening a whole new can of worms, see if ford will give you a schematic of the vacuum system, if its electric controlled any haynes repair manual for your van will have the wiring schematics in the back, if you know how to follow them they will help if not, try the heater control valve first tho, they do go bad no matter what type of vehicle you have, even if its problem is circled alreadyI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?id bet that it is mechanical, the one that i saw yesterday was.
the heater control valve will either have a vacuum hose or a cable on top of it
if both of the hoses are hot you should have heatI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?if its vacuum, you are opening a whole new can of worms, see if ford will give you a schematic of the vacuum system, if its electric controlled any haynes repair manual for your van will have the wiring schematics in the back, if you know how to follow them they will help if not, try the heater control valve first tho, they do go bad no matter what type of vehicle you have, even if its problem is circled alreadyI got 1998 ford E150 van 4.6 No heat ,change thermostat and heater hose are hot core is ok?id bet that it is mechanical, the one that i saw yesterday was.
How do I change the batteries in my vokera rf411 programmable room thermostat?
Hmmm. I just looked at the PDF of your stat. Not very informative. I would contact Vokera Uk technical by phone or email. Go to their site.How do I change the batteries in my vokera rf411 programmable room thermostat?Take the batteries out, put new ones in.
How do I change the thermostat on a 1991 Toyota Previa van?
Here are the instructions. http://www.autozone.com/shopping/repairGHow do I change the thermostat on a 1991 Toyota Previa van?follow top hose back to motor remove hose and two bolts in that housing lift remove thermostat scrape off old gasket replace with new thermo and gasket.. tighten bolts put on hose fill radiator with coolant and crank and check for leaksHow do I change the thermostat on a 1991 Toyota Previa van?Follow the upper radiator hose down to the thermostat housing. Either drain the radiator in a plastic pail or siphon off the contents of the radiator with a piece of inexpensive small diameter hardware-store vinyl hose. Remove the upper radiator hose from the thermostat housing. Remove the small capscrews or bolts from the aluminum thermostat housing. It may be necessary to %26quot;tunk%26quot; the housing with a rubber hammer or pry it off with a screwdriver. If your thermostat gasket is just an O ring it pays to lubricate it with silicone ignition grease before bolting the housing back on. If It's a gasket, wipe both sides with Prematex Blue Silicone Gasket maker before bolting the housing back in place. Remenber that the thermostat goes back in with the spring end pointing down.
Change Thermostat on a 1995 Audi A90 Quattro V6 - need location on vehicle and easiest way to change.?
Orange engine light comes on after driving about 15 to 20 minutes in cold weather. Didn't have problem in summer time --- problem started last winter and returned this winter. Have had codes reset and sensor changed but light still comes on. If I shut the car off and turn it back on, the code resets itself and the light goes off. I get some warm air but not enough for the heat gage to move...even after considerable driving distances. I believe that it is the Thermostat that is causing this problem, but unlike domestic cars which are easily located and changed, I don't know if this is the problem for sure and don't know where to locate the thermostat. Any help would be appreciated...Thanks.Change Thermostat on a 1995 Audi A90 Quattro V6 - need location on vehicle and easiest way to change.?most every car made follow top radiator hose back to motor remove hose remove two bolts lift housing
scrape off old gasket install new thermostat and gasket tighten it all back up crank motor fill with coolant your done and nope thermostat controls how the motor heats and cools and if its bad car either over heats in minutes or you have no heat at all and if you get a light it might be but it wouldnt last a year being bad just minutes or a day.. and your case more of a sensor problem not thermostatcat share printer on 2 computers
scrape off old gasket install new thermostat and gasket tighten it all back up crank motor fill with coolant your done and nope thermostat controls how the motor heats and cools and if its bad car either over heats in minutes or you have no heat at all and if you get a light it might be but it wouldnt last a year being bad just minutes or a day.. and your case more of a sensor problem not thermostat
How do you locate and change out a thermostat in a 2001 ford focus se?
follow the top radiator hose down to the engine the thermostat is located in under that housing where the hose is connected to,drain some of the coolant out of it though before you try to do this other wise you,ll loose quit a but of it,there's a drain on the bottom of the radiator that will allow you to do this,once you have the thermostat in and all tightened back up be sure and re-fill the cooling system on it,and run it check for leaks and your done,fairly easy job if you take your time and don't get in a hurry,good luck with it.How do you locate and change out a thermostat in a 2001 ford focus se?dodge man is wrong.......go here
www.focusfanatic.com
www.focusfanatic.com
I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?
Im not sure where it is located or how to get to itI drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?follow the upper rad hose to the thermostat housing, let the cooling system cool down drain the cooling system remove the upper rad hose remove the thermostat housing remove the thermostat and clean all gasket mating surfaces reinstall the stat with the pointed end up! install the housing and hose fill with coolant and bleed the air from the system by reving the engine to around 4500rpm this should remove the air traped in the block I hope this helpsI drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?Follow the upper rad hose to eng, it is at the bottom of hose, you'll probably need a socket and long extension to get at it the two bolts.I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?Please look under your hood as in most cars its easy to find..
dexterI drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?the above answer is the best, the only thing I would add is to remember which way the thermostat is situated in the housing.
You do not want to install it upside down.
If you have mimimal experience this is an easy replacemet to do.
Just remember which way the thermostat is oriented inthe housing!!!!!!I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?If you have a V8, you will have to remove the a/c compressor, because there is not enough room to remove the hose clamp holding the top hose to the thermostat housing. If you haven't done one before, it can be a daunting situation. You have to unhook the electrical connections from the compressor, remove a nut holding the hose bracket near the alternator. There is enough slack in the a/c hoses to move the compressor to the right side out of the way with out discharging the refrigerant.
The thermostat housing is steel and held on with two bolts, after removing clean all the old gasket off the manifold and housing. Place the thermostat in the manifold long side down, put on the gasket and bolt everything back like you found it. Do not overtighten and strip those bolt holes in the manifold, and tighten both sides evenly.I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?Its located at the dealership's repair shop.I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?It is not a bright idea for you to do it.
Considering you don't even know where it is located or how to do it; I'd say you don't have any experience with tools or engines.
Don't mess with it, risk of doing it wrong are high.
Consecuences are expensive.
dexterI drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?the above answer is the best, the only thing I would add is to remember which way the thermostat is situated in the housing.
You do not want to install it upside down.
If you have mimimal experience this is an easy replacemet to do.
Just remember which way the thermostat is oriented inthe housing!!!!!!I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?If you have a V8, you will have to remove the a/c compressor, because there is not enough room to remove the hose clamp holding the top hose to the thermostat housing. If you haven't done one before, it can be a daunting situation. You have to unhook the electrical connections from the compressor, remove a nut holding the hose bracket near the alternator. There is enough slack in the a/c hoses to move the compressor to the right side out of the way with out discharging the refrigerant.
The thermostat housing is steel and held on with two bolts, after removing clean all the old gasket off the manifold and housing. Place the thermostat in the manifold long side down, put on the gasket and bolt everything back like you found it. Do not overtighten and strip those bolt holes in the manifold, and tighten both sides evenly.I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?Its located at the dealership's repair shop.I drive a 1999 Dodge Durango and need to change the thermostat...where is it located and how do I change it?It is not a bright idea for you to do it.
Considering you don't even know where it is located or how to do it; I'd say you don't have any experience with tools or engines.
Don't mess with it, risk of doing it wrong are high.
Consecuences are expensive.
How can I change the thermostat in a 98 ford escort zx2?
Drain some coolant into a clean container until the coolant level is below the thermostat housing.
Remove the upper radiator hose connection from the thermostat housing.
Loosen the housing bolts and remove the housing.
Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
Install the gasket.
Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
When the engine has reached operating temperature make sure the thermostat opens.
You should be able to see coolant circulating within the radiator.
Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.How can I change the thermostat in a 98 ford escort zx2?take it to a repair stationHow can I change the thermostat in a 98 ford escort zx2?I am not trying to be funny but if you have to ASK this question you should not even TRY to do the job. If you live near South Ockendon contact me and I'll do it for you!How can I change the thermostat in a 98 ford escort zx2?Hope this helps:
http://www.autozone.com/servlet/UiBrokerHow can I change the thermostat in a 98 ford escort zx2?Here is a picture of the thermostat for the Ford 2.0L:
http://www.rockauto.com/ref/Stant/Detail
Remove the upper radiator hose connection from the thermostat housing.
Loosen the housing bolts and remove the housing.
Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
Install the gasket.
Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
When the engine has reached operating temperature make sure the thermostat opens.
You should be able to see coolant circulating within the radiator.
Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.How can I change the thermostat in a 98 ford escort zx2?take it to a repair stationHow can I change the thermostat in a 98 ford escort zx2?I am not trying to be funny but if you have to ASK this question you should not even TRY to do the job. If you live near South Ockendon contact me and I'll do it for you!How can I change the thermostat in a 98 ford escort zx2?Hope this helps:
http://www.autozone.com/servlet/UiBrokerHow can I change the thermostat in a 98 ford escort zx2?Here is a picture of the thermostat for the Ford 2.0L:
http://www.rockauto.com/ref/Stant/Detail
How do i change the thermostat in my 2001 vw jetta 1.8t?
The thermostat is behind the alternator. You will likely need to remove the alternator to get the thermostat out.
How do I change the thermostat on my 1998 Buick century?
where is the thermostat on my 1998 Buick CenturyHow do I change the thermostat on my 1998 Buick century?it's located at the opposite end of the upper radiator hose, under the ball shaped metal thing, inside it's own mounting container. Remove the upper radiator hose (large one coming out of the radiator on the driver's side) and then the two or four bolts that hold it down. Careful if it's tough as oftentimes it will strip the screw mounts of the mounting container. Then you'll have to remove the two bolts that hold that on,all the while getting radiator fluid all over.
MAKE SURE TO DRAIN SOME RADIATOR FLUID FROM THE RADIATOR, and that the CAR IS COLD.
Replace the gasket, and use some silicon gasket sealer on both surfaces for trouble free installation. Also this holds that darn gasket in place better as you tighten up. Don't over tighten as you need to let the heat expand first, after running to check for leaks (about 5 minute run-time) then tighten a little if need be. hope this helpsittwit initiate legal case for
MAKE SURE TO DRAIN SOME RADIATOR FLUID FROM THE RADIATOR, and that the CAR IS COLD.
Replace the gasket, and use some silicon gasket sealer on both surfaces for trouble free installation. Also this holds that darn gasket in place better as you tighten up. Don't over tighten as you need to let the heat expand first, after running to check for leaks (about 5 minute run-time) then tighten a little if need be. hope this helps
How do you change the radiator thermostat on a 1995 Buick Rivera?
Drain water, remove the hose, remove the thermostat, scrape off old seal, replace seal and thermostat, and place hose back on it. pretty much the same way you would do it on any other vehicle.How do you change the radiator thermostat on a 1995 Buick Rivera?Drain some of the coolant so it will be below the level of where you will be working. Follow the top hose from the radiator to the engine. Remove the two bolts (sometimes three) bolts holding in the housing, remove the bad thermostat. Clean the mating surfaces, insert the new thermostat making sure the gasket is in the right place. Put the bolts back in and tighten, add coolant to the full line, check for leaks.
Tried to change my home thermostat , old one has an orange wire marked o, no mention of o on new thermostat.?
Tried to just tape it and go without but now I have no ac, when I turn ac on it is heat. Tried to hook up orange wire to Rc slot (which I didnt have ) but that didnt work either??????Tried to change my home thermostat , old one has an orange wire marked o, no mention of o on new thermostat.?You must have a heat pump and have the wrong thermostat.
You need a heat pump thermostat that will have the %26quot;O%26quot; or orange connection.
The %26quot;O%26quot; is for the reversing value which switches the valve between heat and cool.
This is why you are getting heat in the cool because you don't have the %26quot;O%26quot; connection.
Sorry to tell ya.Tried to change my home thermostat , old one has an orange wire marked o, no mention of o on new thermostat.?sounds like you need an expert. sorry can't help
You need a heat pump thermostat that will have the %26quot;O%26quot; or orange connection.
The %26quot;O%26quot; is for the reversing value which switches the valve between heat and cool.
This is why you are getting heat in the cool because you don't have the %26quot;O%26quot; connection.
Sorry to tell ya.Tried to change my home thermostat , old one has an orange wire marked o, no mention of o on new thermostat.?sounds like you need an expert. sorry can't help
How can I change the battery of my home's Beutler thermostat?
Buetler is the name of a Heating and Air Conditioning contractor. Contractors often have their name and phone # printed on thermostats that they buy in bulk. If you can take the thermostat off of the wall plate you can probably find another Manufacturer name or model #. If this is a contractor branded thermostat it is probably acutally a Honeywell, White-Rodgers, Robertshaw or Braeburn thermostat. In any case theres a good chance that after you remove the thermostat from the wall plate you will see where to change the batteries if the thermostat takes batteries. Many digital thermostats are powered by the air conditioning equipment and do not have batteries. If your not seeing a low battery indicator and you just have a blank screen you may have a problem with the indoor section of your heating and air conditioning equipment.How can I change the battery of my home's Beutler thermostat?Flip open the door and change it! It depends on your model but it might be as simple as putting a pair of AA alkalines in,
Thermostat furnace change?
I would like to change my thermostat from the wired in type that I have now to a wireless type. Is it hard to install? How do I do it? My furnace is oil/hot air.Thermostat furnace change?First make sure you have a thermostat that will work with your kind of heat. (gas, electric, heat pump) Then turn of the power to your unit so you do not blow the transformer. You will need a small straight blade screwdriver and then just follow the directions.
How do you change thermostat on 97 ford taurus sho?
1. Drain the coolant until the level of the coolant is below the level of the thermostat.
2. Disconnect the battery cables (negative cable first).
3. Remove the battery from the vehicle.
4. Remove the power distribution box.
5. Remove the battery tray.
6. Disconnect the upper radiator hose and position it out of the way.
7. Disconnect the lower radiator hose from the water inlet connection.
8. Unfasten the two water inlet connection retaining bolts and remove the water inlet connection.
9. Remove the O-ring seal and thermostat from the water pump. Inspect the O-ring for damage and replace as necessary.
To install:
10. Clean the water inlet connection mating surfaces.
11. Install the O-ring, thermostat and the water inlet connection. Refer to the accompanying illustration if you can't remember how the O-ring and thermostat are positioned.
12. Install the water inlet connection assembly retainers and tighten them alternately to 71-106 inch lbs. (8-12 Nm).
13. Connect the lower radiator hose to the water inlet connection.
14. Install the upper radiator hose.
15. Install the battery tray, power distribution box ad the battery.
16. Connect the battery cables (negative last).
17. Fill the engine with coolant, start the engine and check for leaks.
18. Stop the engine and top off the coolant recovery reservoir as necessary.
http://repairguide.autozone.com/znetrgs/How do you change thermostat on 97 ford taurus sho?http://www.ehow.com/how_4661904_replace-
Follow the big black rubber upper radiator hose from the radiator to the engine. The engine coolant thermostat should be under the bell shaped housing mounted to the engine where that hose connects to it. Make sure you put the new thermostat in the same way the old one was (NOT reversed!) Use a new gasket. It's a good time to flush the coolant system real well by temporarily leaving the old thermostat out and reconnecting the radiator hose to allow free flow for flushing. Then install the new thermostat and new coolant mix.How do you change thermostat on 97 ford taurus sho?open hood follow top radiator hose to motor remove hose remove two bolts lift housing lift thermostat scrape off old gasket replace new gaske and new thermostat
type into search box how to replace name of part
how to replace thermostatgot a call saying fish
2. Disconnect the battery cables (negative cable first).
3. Remove the battery from the vehicle.
4. Remove the power distribution box.
5. Remove the battery tray.
6. Disconnect the upper radiator hose and position it out of the way.
7. Disconnect the lower radiator hose from the water inlet connection.
8. Unfasten the two water inlet connection retaining bolts and remove the water inlet connection.
9. Remove the O-ring seal and thermostat from the water pump. Inspect the O-ring for damage and replace as necessary.
To install:
10. Clean the water inlet connection mating surfaces.
11. Install the O-ring, thermostat and the water inlet connection. Refer to the accompanying illustration if you can't remember how the O-ring and thermostat are positioned.
12. Install the water inlet connection assembly retainers and tighten them alternately to 71-106 inch lbs. (8-12 Nm).
13. Connect the lower radiator hose to the water inlet connection.
14. Install the upper radiator hose.
15. Install the battery tray, power distribution box ad the battery.
16. Connect the battery cables (negative last).
17. Fill the engine with coolant, start the engine and check for leaks.
18. Stop the engine and top off the coolant recovery reservoir as necessary.
http://repairguide.autozone.com/znetrgs/How do you change thermostat on 97 ford taurus sho?http://www.ehow.com/how_4661904_replace-
Follow the big black rubber upper radiator hose from the radiator to the engine. The engine coolant thermostat should be under the bell shaped housing mounted to the engine where that hose connects to it. Make sure you put the new thermostat in the same way the old one was (NOT reversed!) Use a new gasket. It's a good time to flush the coolant system real well by temporarily leaving the old thermostat out and reconnecting the radiator hose to allow free flow for flushing. Then install the new thermostat and new coolant mix.How do you change thermostat on 97 ford taurus sho?open hood follow top radiator hose to motor remove hose remove two bolts lift housing lift thermostat scrape off old gasket replace new gaske and new thermostat
type into search box how to replace name of part
how to replace thermostat
How do I change a thermostat on a 2000 Chevy Blazer 4.3L?
follow the top radiator hose to the engine, the thermostat is inside the thing that the hose bolts to, remove the bolts that hold it to the intake manifold, there are two, 14mm or 9/16%26quot; size
very easy job
of the thermostat is bad the engine will overheat at all time, also if the waterpump or radiator are bad
if its getting hot only at idle and slow speed then its not the thermostat, it would be the fan not working almost always, the clutch in it is worn out, or if its electric thne it doesnt come on when the temp switch says to
good luck
very easy job
of the thermostat is bad the engine will overheat at all time, also if the waterpump or radiator are bad
if its getting hot only at idle and slow speed then its not the thermostat, it would be the fan not working almost always, the clutch in it is worn out, or if its electric thne it doesnt come on when the temp switch says to
good luck
How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?
Rostislav, you have two options: Given that it is a relatively small job, you can see if a handyman does it or just seek the person who ought to know about doing it for sure, and that's an electrician. Fortunately, there are plenty of local handyman and electrical contractors seeking to give free estimates with no obligation, and taking advantage of this is the consumer-smart way to go about finding an accurate answer to your question. It's important that you get a local estimate and not rely on guesses found here on Yah, as a lot of factors really bear on the cost of such a project, including the following: The cost of material and labor greatly varies by location.
As I said, Free estimates from either local handyman contractors or electrical contractors are the key to your success in this home improvement project of yours. Here's a great link to a handyman site that offers free very resourceful information to assist you in determining the cost of your project, and, ultimately, selecting a local contractor in an effort to get the best deal for you:
HANDYMAN CONTRACTOR INFO:
http://yourhandymanzone.com/Your_Handyma
ELECTRICAL CONTRACTOR INFO:
http://yourhandymanzone.com/Your_Handyma
I'm sure you'll find the information you need, specifically the tips, useful as it relates to being treated fairly by contractors and exploring the consumer-wise approach of getting free written estimates to find the best contractor in your area.
.
.
Source(s):
The Internet is what I use. I'm pretty knowledgeable about the Internet. I have a firm belief in helping people with what I know, including from my development of sites, such as the one cited above. Sharing really is caring, and I wish those who I help can reciprocate by sharing what they know.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?Depends on what you're after .. A programmable thermostat can cost between $30 and 120 The kitchen light can cost between $10.00 on clearance to $150 for a decent ceiling fan. The plug $ 2.00 to $ 30.00 for a GFIHow much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?That is all very easy work and would probably be better if you did it yourself. As a heating company, for me to come out and install a new thermostat for you would be the standard $150 service call (that's with you already having a stat). You can try to get a handy man or pretty much any guy who has any experience with a screw driver to do it for $40.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?I'd charge 65 quid.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?If you are at all mechanically inclined you could do this yourself, and if not and electrican would charge you a service fee. This price will vary but the company I work for charges $65.
As I said, Free estimates from either local handyman contractors or electrical contractors are the key to your success in this home improvement project of yours. Here's a great link to a handyman site that offers free very resourceful information to assist you in determining the cost of your project, and, ultimately, selecting a local contractor in an effort to get the best deal for you:
HANDYMAN CONTRACTOR INFO:
http://yourhandymanzone.com/Your_Handyma
ELECTRICAL CONTRACTOR INFO:
http://yourhandymanzone.com/Your_Handyma
I'm sure you'll find the information you need, specifically the tips, useful as it relates to being treated fairly by contractors and exploring the consumer-wise approach of getting free written estimates to find the best contractor in your area.
.
.
Source(s):
The Internet is what I use. I'm pretty knowledgeable about the Internet. I have a firm belief in helping people with what I know, including from my development of sites, such as the one cited above. Sharing really is caring, and I wish those who I help can reciprocate by sharing what they know.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?Depends on what you're after .. A programmable thermostat can cost between $30 and 120 The kitchen light can cost between $10.00 on clearance to $150 for a decent ceiling fan. The plug $ 2.00 to $ 30.00 for a GFIHow much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?That is all very easy work and would probably be better if you did it yourself. As a heating company, for me to come out and install a new thermostat for you would be the standard $150 service call (that's with you already having a stat). You can try to get a handy man or pretty much any guy who has any experience with a screw driver to do it for $40.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?I'd charge 65 quid.How much do you think it would cost to change a light in the kitchen, replace an old thermostat, and a plug?If you are at all mechanically inclined you could do this yourself, and if not and electrican would charge you a service fee. This price will vary but the company I work for charges $65.
Is it a easy job to change a thermostat on a 2001 mk3 petrol mondeo?
not really, but if your mechanically inclined you should be okIs it a easy job to change a thermostat on a 2001 mk3 petrol mondeo?aA little bit fiddley but quite an easy job really ,a little warning though do not try and force it out if you are having trouble moving it do not jerk it cause if it snaps in place you will have a hell of a job getting it out,spray it well with WD40 and leave it over night then try to tighten it to break the seal and then undo it.Hope this helps.
Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?
leave it set at one temperature and hear is why when you turn your thermostat down every thing in your house also gets down to that temperature and your furnace has to work twice as hard to warm every thing back up to your normal at home temperatureIs it cheaper to leave your thermostat at one temperature constantly or change it though out the day?Use a programmable thermostat and set it lower in the evenings when you are asleep.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?If no one is home during the day, turn it down. Turn it back up when you get home.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?Both are right. You can buy reasonable set back thermostats that will program a number of different times on and off and which have overrides if you feel the need for a bit more heat or unexpectedly need it.
Studies by utility companies agree if no one is home and the place doesn't need a lot of heat for sensitive pets, etc., use the setbacks. The energy costs are considered less to bring a place back to usual temp than to keep it on same setting all day. I have used one for years and did notice a bit of difference in therms used.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?You can change it once.
Have a temperature for when you are awake and one for when you are asleep or away from home.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?You can save 10-15% on your bill by replacing your thermostat with a programmable unit. It is an easy do it yourself project and not very expensive. For a step by step guide, check out the thermostat page at www.hvac-for-beginners.comIs it cheaper to leave your thermostat at one temperature constantly or change it though out the day?All of these are very good answers. Just be sure not to vary your degree of change by more than 2 degrees. Everything has to be %26quot;heated%26quot; in the room, not just the air, to bring to temp.
Studies by utility companies agree if no one is home and the place doesn't need a lot of heat for sensitive pets, etc., use the setbacks. The energy costs are considered less to bring a place back to usual temp than to keep it on same setting all day. I have used one for years and did notice a bit of difference in therms used.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?You can change it once.
Have a temperature for when you are awake and one for when you are asleep or away from home.Is it cheaper to leave your thermostat at one temperature constantly or change it though out the day?You can save 10-15% on your bill by replacing your thermostat with a programmable unit. It is an easy do it yourself project and not very expensive. For a step by step guide, check out the thermostat page at www.hvac-for-beginners.comIs it cheaper to leave your thermostat at one temperature constantly or change it though out the day?All of these are very good answers. Just be sure not to vary your degree of change by more than 2 degrees. Everything has to be %26quot;heated%26quot; in the room, not just the air, to bring to temp.
Why does it feel so cold in my apartment?? I do not change the thermostat at all. I leave it at 68 degrees day?
and night.
So how come it seems so cold during the day when it's actually warmer outside? And at night, when it's colder, it seems so hot inside I can barely stand it. I'm just curious about the science behind this.Why does it feel so cold in my apartment?? I do not change the thermostat at all. I leave it at 68 degrees day?contrastmyspace cursors msdn
So how come it seems so cold during the day when it's actually warmer outside? And at night, when it's colder, it seems so hot inside I can barely stand it. I'm just curious about the science behind this.Why does it feel so cold in my apartment?? I do not change the thermostat at all. I leave it at 68 degrees day?contrast
Changing the thermostat in a Ford Aspire?
I need to change to the thermostat in a 1994 Ford Aspire. The bottom bolt holding the thermostat cover is impossible to reach with a socket or wrench. There is a metal coolant tube that is in front of the bottom bolt. I can't come from the side of the bolt because the thermostat cover prevents it. Does anyone know an easy way to reach the thermostat on this car ?Changing the thermostat in a Ford Aspire?i always say buy a shop manual...best 15 dollars/pounds you can spend...step by step...and next time at the shop u will know more and b less likely to get ripped off.Changing the thermostat in a Ford Aspire?A friend of mine has one but his is a year newer than yours.He had me do work on his because it needed a lot of work on it.The way to get to that bottom bolt is to remove the tube your talking about.The book I used to fix his was a chiltons manual.Everything that I had to fix on his was easy to do.hgm20002000@yahoo.com
Want change my dial Thermostat to a digital one. have electric heat. where to find the right one?
went to home deport, and they recomend the wrong one, havign trouble installing today and went back to them again and relaized the one they sold me is not for electric heat. is there any place I can get local without going on line? Live in Boston area.Want change my dial Thermostat to a digital one. have electric heat. where to find the right one?You may need a line voltage thermostat if you have electric baseboard heaters. They are available at most hardware stores.
If you have an electric furnace you should be able to use a standard 24 volt thermostat and just set it up for electric for the cycle rate.Want change my dial Thermostat to a digital one. have electric heat. where to find the right one?try burner suppy on river st. in beverly.Want change my dial Thermostat to a digital one. have electric heat. where to find the right one? Most thermostats (Including digital) need to be set for electric or gas. Just a dip switch to flip. You should be able to get one at any DIY center or HVAC supply house.
If you have an electric furnace you should be able to use a standard 24 volt thermostat and just set it up for electric for the cycle rate.Want change my dial Thermostat to a digital one. have electric heat. where to find the right one?try burner suppy on river st. in beverly.Want change my dial Thermostat to a digital one. have electric heat. where to find the right one? Most thermostats (Including digital) need to be set for electric or gas. Just a dip switch to flip. You should be able to get one at any DIY center or HVAC supply house.
How do I change a Sears non-programmable thermostat five wire Heat/Cool to Noma Programmable Digital 4 wire
I have old Sears model with wires labled white -W , blue-G , red-RC , orange Y ,black -RH , and want to change over to a new programmable digital Noma 5+1+1 with these wires green, yellow, red, and white.Can you help me know which posts to put these wires onto.
Many ThanksHow do I change a Sears non-programmable thermostat five wire Heat/Cool to Noma Programmable Digital 4 wiresounds like you have a heat pump. the new stat wont work for a heat pump. there is no O terminal for the reversing valve.
if you really do have a heat pump, a programmable stat really is not for you. heat pumps really want to keep your house at an even temp. if you try to swing the temp too much you will put the heat pump into emer heat mode and spend twice the money that you would have saved.
put your old stat back on, and get your money back for the programmable one.
possum,hvac guyHow do I change a Sears non-programmable thermostat five wire Heat/Cool to Noma Programmable Digital 4 wirered-r /white-w /green-g/yellow-y
Many ThanksHow do I change a Sears non-programmable thermostat five wire Heat/Cool to Noma Programmable Digital 4 wiresounds like you have a heat pump. the new stat wont work for a heat pump. there is no O terminal for the reversing valve.
if you really do have a heat pump, a programmable stat really is not for you. heat pumps really want to keep your house at an even temp. if you try to swing the temp too much you will put the heat pump into emer heat mode and spend twice the money that you would have saved.
put your old stat back on, and get your money back for the programmable one.
possum,hvac guyHow do I change a Sears non-programmable thermostat five wire Heat/Cool to Noma Programmable Digital 4 wirered-r /white-w /green-g/yellow-y
My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?
when i turn the car off i hear gurgling behind the dash board.My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?What's the year make and model of your car. If it's over 10 years old your radiator owes you nothing. Scale, corrosion and rust builds up in an unmaintained cooling system. The cooling system should be drained flushed cleaned before spending money on a new radiator.
Are the electric fans running? Is the radiator cross-tubes and fins clean? Drain and flush the system. Try two 33 oz. plastic bottles of Prestone Super Radiator cleaner fill till full with plain water. Drive the car at least 200 miles before draining and flushing again.My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?That's some BS. Take it to the mechanic for more tests... run the heat on full blast to help cool the engine for now... does it happen to be a PT or another crysler? wouldn't surprise me in the least...My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?go to the repair shop, sounds like your Rad or water pump is gone.My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?One of two things. Either your radiator is not full or you've added too much antifreeze or you only have antifreeze in your radiator. It's suppose to be 50/50 mixture. Antifreeze holds heat better than water, that's why it's great to have it in the summer. It doesn't react to heat as fast. However, too much antifreeze holds too much heat and causes your car to over heat. Does your radiator/hoses have any leaks or did it and you were adding straight antifreeze.ie hosted control remove sunless tanning spray
Are the electric fans running? Is the radiator cross-tubes and fins clean? Drain and flush the system. Try two 33 oz. plastic bottles of Prestone Super Radiator cleaner fill till full with plain water. Drive the car at least 200 miles before draining and flushing again.My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?That's some BS. Take it to the mechanic for more tests... run the heat on full blast to help cool the engine for now... does it happen to be a PT or another crysler? wouldn't surprise me in the least...My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?go to the repair shop, sounds like your Rad or water pump is gone.My car is over heating i change the thermostat, but it is still over heating when i drive long distance.?One of two things. Either your radiator is not full or you've added too much antifreeze or you only have antifreeze in your radiator. It's suppose to be 50/50 mixture. Antifreeze holds heat better than water, that's why it's great to have it in the summer. It doesn't react to heat as fast. However, too much antifreeze holds too much heat and causes your car to over heat. Does your radiator/hoses have any leaks or did it and you were adding straight antifreeze.
With a programmable thermostat by enerstat, how do I change from f to c?
Without knowing exactly which model it is, it's tricky to know for sure. I've attached a link to at least one Enerstat users manual. It says that you should simultaneously press the %26quot;s%26quot; and %26quot;t%26quot; buttons.
Even if this isn't exactly your unit, its worth a try.
Even if this isn't exactly your unit, its worth a try.
My thermostat reads change water panel. What does that mean?
your air conditioner probably is a dehumidifier as well and needs the water panel changed.My thermostat reads change water panel. What does that mean?change the panel.My thermostat reads change water panel. What does that mean?Sounds like it got some humidity in it from the heat. And oh yea, probably want to change that water panel real soon, k?My thermostat reads change water panel. What does that mean?thermostsat for what?
Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?
Would changing the thermostat back up and down 2-3 degrees affect electricity usage rather than keeping it at one temperature. For example, my roomates like to change the thermostat around 2 degrees lower at night then change it up again in the day.
I always thought this would cause the AC to work harder to maintain the temperature, thus leading to a high electricity bill.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?The rule of thumb is that you can save about 3% on your heating bill for every degree that you set back your thermostatDoes constantly changing the thermostat temperature 2-3 degrees affect electricity usage?yes
we did a 2 yr study on changing the temp at night and turning it back up in the am, with a programmable thermostat,
we dropped the temp 5 deg at night, then back to 70 at day time
for 1 yr then we removed the programmable one and went to a standard thermostat, and left it at 69 deg 24/7
we saved over $1,000 a yr on the electric and fuel bill with the standard thermostat.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?Ultimately depends on the time of year. I'm assuming we're talking about the summer because you said AC. If you turn the thermostat higher during the day (when its hotter), then the AC unit will work less often, thus saving you energy. At the night when it's cooler, even though the AC thermostat has been lowered, the AC unit doesn't have to compete with the sun's direct heat which makes it cheaper to operate.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?Any time you set your thermostat down you save money. Anytime you raise you thermostat it is costing you money.
If you set it down 2 degs you are saving money. If you set it back up to the original setting you will be right back where you started if you hadn't set it down. You save money during the time it is set down and you spend the same money during the time it is set back to the original setting. A net saving.
People so think otherwise have never sat down and done the math.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?adjusting your thermostat 2-3 will only save you money.
adjusting it 10+ is where your theory baffles many. but it still saves money...
the lower the thermostat the more money you will save no matter how much you change it.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?It is all relative . So it all averages out.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?when it goes lower it saves you money that is what you are suppose to do 5degrees is betterDoes constantly changing the thermostat temperature 2-3 degrees affect electricity usage?When you ask, %26quot;Does constantly changing the thermostat....affect electricity usage?%26quot;, the answer is %26quot;Yes, it saves electricity usage.%26quot; Any time you turn something off, you save, and raising the AC thermostat setting will turn the AC off for longer periods of time. You cannot save more than when the unit is off.
However, when you ask, %26quot;Does changing the thermostat cause the AC to work harder to maintain the temperature?%26quot;, again the answer is %26quot;Yes, it will be harder to maintain the desired temp.%26quot; This is where most people think that the catch up time causes the unit to run more and therefore use more electricity. When outside temps are changing, it is harder to illustrate my next point and make comparisons. So, first, consider the following.
Let's say that the outside temp maintains an outside temp of 100 degrees F. Let's also say that the AC in question is able to cool the house to 78 degrees F, and no lower, as long as the outside temp maintains 100 deg. F. If I keep my thermostat at 77 degrees, my AC will run 24/7, and will never turn off. If I raise my thermostat two or three degrees, my AC will enjoy SOME off time, and therefore save SOME electricity. As the thermostat setting is lowered, longer run times will be required of the AC to maintain the lower temp.
The above scenario is almost exactly the way it has been where I live. When the outside temp is approx. 95 to 100, the inside temp of my house would never get below 78 degrees. When my wife and I leave home in the morning, if we keep the thermostat at 72 degrees, the house would be at 78 when I got home in the early afternoon. At night when the outside temp lowers to 70 or 75 degrees, there obviously will be a point when the thermostat will be satisfied and turn off the AC. However the lower the thermostat setting, again the longer the AC will run. I thought that if I kept the AC on all day with the thermostat setting as low as 72, that's the temp I would enjoy when I got home. My AC was never going to be able to reach that temp anyway.
Notice the following quote from Michael Bluejay's website:
%26quot;It's a myth that leaving the AC on while you're away at work uses less energy than turning it on when you get home. Here's why:
Heat goes to where it's not. That's why heat from outside goes into your cooler home. With the AC off, at some point your house will be so hot it can't absorb any more heat. When you come home and turn the AC on, the AC removes all that heat.
But if the AC is on when you're gone, then you've turned your house into a heat magnet. But keeping it artificially cool, there's no limit to the amount of heat it can absorb. It can always absorb more heat. And your AC has to remove that heat constantly. Your AC kicks in and removes some of that heat, then the house is cooler so it sucks in more heat from outside, so your AC kicks in again and removes that heat, and so on.
This means that throughout the day, your house has absorbed way more than one houseful of heat. And your AC had to remove it all. By contrast, with the AC off all day, then it has to remove just one houseful of heat when you come home and turn it on.
Let's say you leave the AC off, and your house absorbs 20k BTU's of heat and then stops, because that's all it can absorb.
Now let's say that you have the AC running instead. The house absorbs 5k BTU's of heat, so the AC kicks in and removes it. Then it absorbs another 5k BTU's, and your AC kicks in and removes that. Repeat that process several times during the day.
The actual numbers will vary, and I haven't tested this to see exactly how much the penalty for leaving the AC on during the day is, but there is zero question that running the AC all the time uses more energy than turning it on when you get home. This is not a gray area, it's simple physics, and no person with any knowledge of this subject disputes it. Running the AC when you're not home wastes energy, period.%26quot;
I hope this helps.
I always thought this would cause the AC to work harder to maintain the temperature, thus leading to a high electricity bill.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?The rule of thumb is that you can save about 3% on your heating bill for every degree that you set back your thermostatDoes constantly changing the thermostat temperature 2-3 degrees affect electricity usage?yes
we did a 2 yr study on changing the temp at night and turning it back up in the am, with a programmable thermostat,
we dropped the temp 5 deg at night, then back to 70 at day time
for 1 yr then we removed the programmable one and went to a standard thermostat, and left it at 69 deg 24/7
we saved over $1,000 a yr on the electric and fuel bill with the standard thermostat.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?Ultimately depends on the time of year. I'm assuming we're talking about the summer because you said AC. If you turn the thermostat higher during the day (when its hotter), then the AC unit will work less often, thus saving you energy. At the night when it's cooler, even though the AC thermostat has been lowered, the AC unit doesn't have to compete with the sun's direct heat which makes it cheaper to operate.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?Any time you set your thermostat down you save money. Anytime you raise you thermostat it is costing you money.
If you set it down 2 degs you are saving money. If you set it back up to the original setting you will be right back where you started if you hadn't set it down. You save money during the time it is set down and you spend the same money during the time it is set back to the original setting. A net saving.
People so think otherwise have never sat down and done the math.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?adjusting your thermostat 2-3 will only save you money.
adjusting it 10+ is where your theory baffles many. but it still saves money...
the lower the thermostat the more money you will save no matter how much you change it.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?It is all relative . So it all averages out.Does constantly changing the thermostat temperature 2-3 degrees affect electricity usage?when it goes lower it saves you money that is what you are suppose to do 5degrees is betterDoes constantly changing the thermostat temperature 2-3 degrees affect electricity usage?When you ask, %26quot;Does constantly changing the thermostat....affect electricity usage?%26quot;, the answer is %26quot;Yes, it saves electricity usage.%26quot; Any time you turn something off, you save, and raising the AC thermostat setting will turn the AC off for longer periods of time. You cannot save more than when the unit is off.
However, when you ask, %26quot;Does changing the thermostat cause the AC to work harder to maintain the temperature?%26quot;, again the answer is %26quot;Yes, it will be harder to maintain the desired temp.%26quot; This is where most people think that the catch up time causes the unit to run more and therefore use more electricity. When outside temps are changing, it is harder to illustrate my next point and make comparisons. So, first, consider the following.
Let's say that the outside temp maintains an outside temp of 100 degrees F. Let's also say that the AC in question is able to cool the house to 78 degrees F, and no lower, as long as the outside temp maintains 100 deg. F. If I keep my thermostat at 77 degrees, my AC will run 24/7, and will never turn off. If I raise my thermostat two or three degrees, my AC will enjoy SOME off time, and therefore save SOME electricity. As the thermostat setting is lowered, longer run times will be required of the AC to maintain the lower temp.
The above scenario is almost exactly the way it has been where I live. When the outside temp is approx. 95 to 100, the inside temp of my house would never get below 78 degrees. When my wife and I leave home in the morning, if we keep the thermostat at 72 degrees, the house would be at 78 when I got home in the early afternoon. At night when the outside temp lowers to 70 or 75 degrees, there obviously will be a point when the thermostat will be satisfied and turn off the AC. However the lower the thermostat setting, again the longer the AC will run. I thought that if I kept the AC on all day with the thermostat setting as low as 72, that's the temp I would enjoy when I got home. My AC was never going to be able to reach that temp anyway.
Notice the following quote from Michael Bluejay's website:
%26quot;It's a myth that leaving the AC on while you're away at work uses less energy than turning it on when you get home. Here's why:
Heat goes to where it's not. That's why heat from outside goes into your cooler home. With the AC off, at some point your house will be so hot it can't absorb any more heat. When you come home and turn the AC on, the AC removes all that heat.
But if the AC is on when you're gone, then you've turned your house into a heat magnet. But keeping it artificially cool, there's no limit to the amount of heat it can absorb. It can always absorb more heat. And your AC has to remove that heat constantly. Your AC kicks in and removes some of that heat, then the house is cooler so it sucks in more heat from outside, so your AC kicks in again and removes that heat, and so on.
This means that throughout the day, your house has absorbed way more than one houseful of heat. And your AC had to remove it all. By contrast, with the AC off all day, then it has to remove just one houseful of heat when you come home and turn it on.
Let's say you leave the AC off, and your house absorbs 20k BTU's of heat and then stops, because that's all it can absorb.
Now let's say that you have the AC running instead. The house absorbs 5k BTU's of heat, so the AC kicks in and removes it. Then it absorbs another 5k BTU's, and your AC kicks in and removes that. Repeat that process several times during the day.
The actual numbers will vary, and I haven't tested this to see exactly how much the penalty for leaving the AC on during the day is, but there is zero question that running the AC all the time uses more energy than turning it on when you get home. This is not a gray area, it's simple physics, and no person with any knowledge of this subject disputes it. Running the AC when you're not home wastes energy, period.%26quot;
I hope this helps.
Subscribe to:
Posts
(Atom)